review33.com: 影音天地: ETSC & ETRC & ESAC Members (44)

分類搜尋 移民 | 借錢 | 投資 | 物流 | 搬運 | 按揭 | 樓盤 | 保險 | 機票 | 酒店 | 升學 | 補習 | 手錶 | 電腦 | 紅酒 | 網購 | 脫髮 | 健身 | 減肥 | 濕疹

影音天地主旨 ﹝請按主旨作出回應﹞ 上頁下頁首頁尾頁

寄件者

傳送日期

[#4705] ETSC & ETRC & ESAC Members (44) ils At least it is a 28".... ^^		Wild_7 正式會員 210.xxx.xxx.252	2007-05-29 10:39

[#4706] ETSC & ETRC & ESAC Members (44)
Yes, it suite the Dali Royal Menuet as praised by 石仔 (now 石哥) in 「音響之路」。

ilovesonatas

正式會員
210.xxx.xxx.22

2007-05-29 10:47

[#4707] ETSC & ETRC & ESAC Members (44)
Please count me in, thanks!

any brothers interested?
-------------------------------------

any more takers? i probably order the rest of the series as well.

drwkng

正式會員
210.xxx.xxx.111

2007-05-29 12:12

[#4708] ETSC & ETRC & ESAC Members (44)
ILS:

In that time, we try many speaker stand including FDII, Sound Anchor, Solid steel and some wooden stand. Actually, Dali match better with Solid steel than the other. Solid steel speaker stand is good not too heavy speaker liker Dali. I think Solid steel will fit Pionner Pure Malt too..

Little_stone

正式會員
220.xxx.xxx.83

2007-05-29 12:20

[#4709] ETSC & ETRC & ESAC Members (44)
Just found the specification of the Aragon 24K that it installed with a quite precised phono stage for mm and mc with adjustable loading/gain :-

Phono Section

Prior to making adjustments for the moving coil section, please be certain the pre-amplifier { NOT plugged Into an A. C. outlet. If you are using a moving magnet or high output moving coil, It Is set up properly at the factory, and you will not need to alter the Inside switches. Please continue to the next section - Power Supply. If you are using a low output moving coil, please read the following:

Soldered onto the circuit board are 3 switches for moving call adjustments. To access them be sure the pre-amp Is unplugged from the A.C. outlet, remove the screws from the top cover, and you will notice 2 switches with 9 positions on the right side of the circuit board. Closer to the center Is a single 2 position switch. For moving call gain, the 2 position switch should have both tabs depressed towards the left (C1 & C3).
The 2 switches on the right adjust loading for the two channels. therefore the adjustments should be identical on both. Each switch, from 1 to 8 will present the following load:

1 - 10 ohms
2 - 25 ohms
3 - 47 ohms
4 - 100 ohms
5 - 249 ohms
6 - 475 ohms
7 - 825 ohms
8 - 1000 ohms

Check with the moving coil manufacturer as to what load is recommended. You will notice that the volume will decrease as you lower the load. i.e. 10 ohms will have less gain than 47,000 ohms.
By combining switches you can create different loads. To know what load you are creating, multiply the two values, then add the two values,
then divide the added value Into the multiplied value to determine the resistance.
Example: switch 4 = 100 ohms
switch 6=475 ohms
Multiply 47,500 / Add 575 = 82.6 ohms

Therefore when switches 4 and 6 are depressed the load is 83 ohms.

ilovesonatas

正式會員
210.xxx.xxx.22

2007-05-29 14:06

[#4710] ETSC & ETRC & ESAC Members (44)
一部打工仔可以 afford 0既石前，內附唔錯0既MC/MM 唱頭放大，較0岩 loading 個「風爐」都幾好聲。

ilovesonatas

正式會員
61.xxx.xxx.86

2007-05-30 00:44

[#4711] ETSC & ETRC & ESAC Members (44)
所有插頭都係「天芬妮」，最可惜坅Y頭版機，窩林係 Noble (Alps) 而唔係 P&G。一隻雷賓石仔路0既八折價，作為大後備都唔錯丫。

ilovesonatas

正式會員
61.xxx.xxx.86

2007-05-30 00:49

[#4712] ETSC & ETRC & ESAC Members (44)
Please count me in, thanks!
--------------------------------

dd,

bought them already. i ordered one more disk so the postage is cheaper. you owe me HK$90^-^

drwkng

正式會員
210.xxx.xxx.111

2007-05-30 12:16

[#4713] ETSC & ETRC & ESAC Members (44)
drwkng

Thanks!

^^

dd845

正式會員
203.xxx.xxx.25

2007-05-30 12:21

[#4714] ETSC & ETRC & ESAC Members (44)
o係音色盧兄套 Altec A5 聽The Mass
動態,氣勢,音色兼而有之
好!!

^^

dd845

正式會員
203.xxx.xxx.25

2007-05-30 12:26

[#4715] ETSC & ETRC & ESAC Members (44)
dd,

bought them already. i ordered one more disk so the postage is cheaper. you owe me HK$90^-^
_________________________________________________

只聽The Mass一cut已物有所值

^^