二手市場主旨 ﹝請按主旨作出回應﹞ 寄件者 傳送日期 由舊至新 由新至舊
[#1] 出售:Classe DR-7 Pre-Amp & DR-3 VHC Power Amp 220V    
價錢 HK$: 48000

HK$: 48000 for both units as one set

A set of RARE Classe flagship Pre-Amp and Power Amp, DR-7 and DR-3 VHC both in 220V setting, is listed for sale. They are the top models in this GOLDEN HANDLE DR series designed by the Classe co-founder, Dave Reich, in the golden age of vinyl and really RARE in the market.

The DR-7 Pre-Amp and DR-3 VHC Power Amp are in 100% excellent working condition without any problem. The cosmetic condition of the DR-7 is about 90% new and the DR-3 VHC is about 85% new, conservatively speaking.

Both units are 100% original without modification except

1> The rubber feet of the DR-3 VHC have been replaced with the bigger ones for better support due to the weight.
2> The power switch of the power supply in the DR-7 was replaced with an original parts as it was broken due to age.

The power supply of the DR-7 had original voltage as 120V but it has been changed to support 220V now by changing the internal setting inside the power supply itself, so both units are now running in 220V voltage and NO external step down transformer is required any more.

Please also find the following product information as reference:

The DR-7 Pre-Amp

- 2 Phono input, PHONO1 and PHONO2, both support MM and MC.

- For MC phono input, it is supported the MC HEADAMP boards, NIL-3, inside which is SELF-ADJUSTING the Input Impedance with factory set the nominal gain of 27 dB, and the gain can be adjusted by using the resistor in different ohm value.

- For MM phono input, it supports the following different Impedance and Capacitance:

3, 5 ,10, 47, 100, 470, 10k, 33k, 47k, 100k ohm and SPARE
47, 100, 150, 220, 330 and 470 pf.

- 5 Line Inputs, CD, TUNER, AUX, TAPE1 and TAPE2

- 2 Line Outputs, TAPE1 and TAPE2 as well as 2 Main Outputs, MAIN 1 and 2.

- The CD input as 2 different modes to operate, FILTERED and DIRECT, where it has 5 filters dip switches to attenuate the high frequency response of CD players.

- It has STAR GROUNDING Bus Bar to prevent ground loops and reduce the noise floor.

- It has separate power supply with Swiss Lemo Fischer termination at both side by connecting with an original factory made cable with Fischer connectors. 5 individual transformers are used inside the power supply for supporting different function/operation of the DR-7 Pre-Amp.

- Its weight is about 25 Kg.

- A copy of user manual is included.

The DR-3 VHC Power Amp

- It is a PURE Class A High Current Design Power Amp without RELAY built inside.

- 45W output per Channel.

- It has two transformer inside for due channels operation.

- The DR-3 VHC in now running in STEREO mode and it can be set as a MONO BLOCK for operation. If setting as mono block, you need two for stereo setup.

- Its weight is about 45 Kg.

Please contact me via PM for whom is serious and interested to them. Thank you.

*** Some extra spare parts in NEW, such as Philips 4700u 40V capacitors and power switch of DR-7 power supply, will be given for free as gift for back up and long term maintenance to someone take the whole set as one go without bargain.

Following photos are for your reference only:

https://farm1.staticflickr.com/922/43099959001_271f093af7_b.jpg

https://farm2.staticflickr.com/1763/41299277780_3351526247_b.jpg

https://farm1.staticflickr.com/919/43439741681_8faae1a6b9_b.jpg

https://farm2.staticflickr.com/1770/29227476618_50a046411f_b.jpg

https://farm1.staticflickr.com/842/41288602240_88ab81b591_b.jpg

* Note: There are 6 original large capacitors, in RED color, under the green main board inside the power supply.

https://farm1.staticflickr.com/837/43099960251_6241a68eb2_b.jpg

https://farm2.staticflickr.com/1827/29227478508_ce9b37c15b_b.jpg




最後修改時間: 2019-03-28 23:56:00
wlhuen
個人訊息 會員
138.xxx.xxx.142
2019-03-28 23:55
[#2] 出售:Classe DR-7 Pre-Amp & DR-3 VHC Power Amp 220V    
價錢 HK$: 48000

HK$: 48000 for both units as one set

A set of RARE Classe flagship Pre-Amp and Power Amp, DR-7 and DR-3 VHC both in 220V setting, is listed for sale. They are the top models in this GOLDEN HANDLE DR series designed by the Classe co-founder, Dave Reich, in the golden age of vinyl and really RARE in the market.

The DR-7 Pre-Amp and DR-3 VHC Power Amp are in 100% excellent working condition without any problem. The cosmetic condition of the DR-7 is about 90% new and the DR-3 VHC is about 85% new, conservatively speaking.

Both units are 100% original without modification except

1> The rubber feet of the DR-3 VHC have been replaced with the bigger ones for better support due to the weight.
2> The power switch of the power supply in the DR-7 was replaced with an original parts as it was broken due to age.

The power supply of the DR-7 had original voltage as 120V but it has been changed to support 220V now by changing the internal setting inside the power supply itself, so both units are now running in 220V voltage and NO external step down transformer is required any more.

Please also find the following product information as reference:

The DR-7 Pre-Amp

- 2 Phono input, PHONO1 and PHONO2, both support MM and MC.

- For MC phono input, it is supported the MC HEADAMP boards, NIL-3, inside which is SELF-ADJUSTING the Input Impedance with factory set the nominal gain of 27 dB, and the gain can be adjusted by using the resistor in different ohm value.

- For MM phono input, it supports the following different Impedance and Capacitance:

3, 5 ,10, 47, 100, 470, 10k, 33k, 47k, 100k ohm and SPARE
47, 100, 150, 220, 330 and 470 pf.

- 5 Line Inputs, CD, TUNER, AUX, TAPE1 and TAPE2

- 2 Line Outputs, TAPE1 and TAPE2 as well as 2 Main Outputs, MAIN 1 and 2.

- The CD input as 2 different modes to operate, FILTERED and DIRECT, where it has 5 filters dip switches to attenuate the high frequency response of CD players.

- It has STAR GROUNDING Bus Bar to prevent ground loops and reduce the noise floor.

- It has separate power supply with Swiss Lemo Fischer termination at both side by connecting with an original factory made cable with Fischer connectors. 5 individual transformers are used inside the power supply for supporting different function/operation of the DR-7 Pre-Amp.

- Its weight is about 25 Kg.

- A copy of user manual is included.

The DR-3 VHC Power Amp

- It is a PURE Class A High Current Design Power Amp without RELAY built inside.

- 45W output per Channel.

- It has two transformer inside for due channels operation.

- The DR-3 VHC in now running in STEREO mode and it can be set as a MONO BLOCK for operation. If setting as mono block, you need two for stereo setup.

- Its weight is about 45 Kg.

Please contact me via PM for whom is serious and interested to them. Thank you.

*** Some extra spare parts in NEW, such as Philips 4700u 40V capacitors and power switch of DR-7 power supply, will be given for free as gift for back up and long term maintenance to someone take the whole set as one go without bargain.

Following photos are for your reference only:

https://farm1.staticflickr.com/922/43099959001_271f093af7_b.jpg

https://farm2.staticflickr.com/1763/41299277780_3351526247_b.jpg

https://farm1.staticflickr.com/919/43439741681_8faae1a6b9_b.jpg

https://farm2.staticflickr.com/1770/29227476618_50a046411f_b.jpg

https://farm1.staticflickr.com/842/41288602240_88ab81b591_b.jpg

* Note: There are 6 original large capacitors, in RED color, under the green main board inside the power supply.

https://farm1.staticflickr.com/837/43099960251_6241a68eb2_b.jpg

https://farm2.staticflickr.com/1827/29227478508_ce9b37c15b_b.jpg


wlhuen
個人訊息 會員
138.xxx.xxx.142
2019-04-08 00:24
[#3] 出售:Classe DR-7 Pre-Amp & DR-3 VHC Power Amp 220V    
Are the items available?
ec4
個人訊息 會員
223.xxx.xxx.144
2019-04-13 00:46
[#4] 出售:Classe DR-7 Pre-Amp & DR-3 VHC Power Amp 220V    
價錢 HK$: 48000

HK$: 48000 for both units as one set

A set of RARE Classe flagship Pre-Amp and Power Amp, DR-7 and DR-3 VHC both in 220V setting, is listed for sale. They are the top models in this GOLDEN HANDLE DR series designed by the Classe co-founder, Dave Reich, in the golden age of vinyl and really RARE in the market.

The DR-7 Pre-Amp and DR-3 VHC Power Amp are in 100% excellent working condition without any problem. The cosmetic condition of the DR-7 is about 90% new and the DR-3 VHC is about 85% new, conservatively speaking.

Both units are 100% original without modification except

1> The rubber feet of the DR-3 VHC have been replaced with the bigger ones for better support due to the weight.
2> The power switch of the power supply in the DR-7 was replaced with an original parts as it was broken due to age.

The power supply of the DR-7 had original voltage as 120V but it has been changed to support 220V now by changing the internal setting inside the power supply itself, so both units are now running in 220V voltage and NO external step down transformer is required any more.

Please also find the following product information as reference:

The DR-7 Pre-Amp

- 2 Phono input, PHONO1 and PHONO2, both support MM and MC.

- For MC phono input, it is supported the MC HEADAMP boards, NIL-3, inside which is SELF-ADJUSTING the Input Impedance with factory set the nominal gain of 27 dB, and the gain can be adjusted by using the resistor in different ohm value.

- For MM phono input, it supports the following different Impedance and Capacitance:

3, 5 ,10, 47, 100, 470, 10k, 33k, 47k, 100k ohm and SPARE
47, 100, 150, 220, 330 and 470 pf.

- 5 Line Inputs, CD, TUNER, AUX, TAPE1 and TAPE2

- 2 Line Outputs, TAPE1 and TAPE2 as well as 2 Main Outputs, MAIN 1 and 2.

- The CD input as 2 different modes to operate, FILTERED and DIRECT, where it has 5 filters dip switches to attenuate the high frequency response of CD players.

- It has STAR GROUNDING Bus Bar to prevent ground loops and reduce the noise floor.

- It has separate power supply with Swiss Lemo Fischer termination at both side by connecting with an original factory made cable with Fischer connectors. 5 individual transformers are used inside the power supply for supporting different function/operation of the DR-7 Pre-Amp.

- Its weight is about 25 Kg.

- A copy of user manual is included.

The DR-3 VHC Power Amp

- It is a PURE Class A High Current Design Power Amp without RELAY built inside.

- 45W output per Channel.

- It has two transformer inside for due channels operation.

- The DR-3 VHC in now running in STEREO mode and it can be set as a MONO BLOCK for operation. If setting as mono block, you need two for stereo setup.

- Its weight is about 45 Kg.

Please contact me via PM for whom is serious and interested to them. Thank you.

*** Some extra spare parts in NEW, such as Philips 4700u 40V capacitors and power switch of DR-7 power supply, will be given for free as gift for back up and long term maintenance to someone take the whole set as one go without bargain.

Following photos are for your reference only:

https://farm1.staticflickr.com/922/43099959001_271f093af7_b.jpg

https://farm2.staticflickr.com/1763/41299277780_3351526247_b.jpg

https://farm1.staticflickr.com/919/43439741681_8faae1a6b9_b.jpg

https://farm2.staticflickr.com/1770/29227476618_50a046411f_b.jpg

https://farm1.staticflickr.com/842/41288602240_88ab81b591_b.jpg

* Note: There are 6 original large capacitors, in RED color, under the green main board inside the power supply.

https://farm1.staticflickr.com/837/43099960251_6241a68eb2_b.jpg

https://farm2.staticflickr.com/1827/29227478508_ce9b37c15b_b.jpg


wlhuen
個人訊息 會員
138.xxx.xxx.142
2019-04-22 23:36
[#5] 出售:Classe DR-7 Pre-Amp & DR-3 VHC Power Amp 220V    
價錢 HK$: 48000

HK$: 48000 for both units as one set

A set of RARE Classe flagship Pre-Amp and Power Amp, DR-7 and DR-3 VHC both in 220V setting, is listed for sale. They are the top models in this GOLDEN HANDLE DR series designed by the Classe co-founder, Dave Reich, in the golden age of vinyl and really RARE in the market.

The DR-7 Pre-Amp and DR-3 VHC Power Amp are in 100% excellent working condition without any problem. The cosmetic condition of the DR-7 is about 90% new and the DR-3 VHC is about 85% new, conservatively speaking.

Both units are 100% original without modification except

1> The rubber feet of the DR-3 VHC have been replaced with the bigger ones for better support due to the weight.
2> The power switch of the power supply in the DR-7 was replaced with an original parts as it was broken due to age.

The power supply of the DR-7 had original voltage as 120V but it has been changed to support 220V now by changing the internal setting inside the power supply itself, so both units are now running in 220V voltage and NO external step down transformer is required any more.

Please also find the following product information as reference:

The DR-7 Pre-Amp

- 2 Phono input, PHONO1 and PHONO2, both support MM and MC.

- For MC phono input, it is supported the MC HEADAMP boards, NIL-3, inside which is SELF-ADJUSTING the Input Impedance with factory set the nominal gain of 27 dB, and the gain can be adjusted by using the resistor in different ohm value.

- For MM phono input, it supports the following different Impedance and Capacitance:

3, 5 ,10, 47, 100, 470, 10k, 33k, 47k, 100k ohm and SPARE
47, 100, 150, 220, 330 and 470 pf.

- 5 Line Inputs, CD, TUNER, AUX, TAPE1 and TAPE2

- 2 Line Outputs, TAPE1 and TAPE2 as well as 2 Main Outputs, MAIN 1 and 2.

- The CD input as 2 different modes to operate, FILTERED and DIRECT, where it has 5 filters dip switches to attenuate the high frequency response of CD players.

- It has STAR GROUNDING Bus Bar to prevent ground loops and reduce the noise floor.

- It has separate power supply with Swiss Lemo Fischer termination at both side by connecting with an original factory made cable with Fischer connectors. 5 individual transformers are used inside the power supply for supporting different function/operation of the DR-7 Pre-Amp.

- Its weight is about 25 Kg.

- A copy of user manual is included.

The DR-3 VHC Power Amp

- It is a PURE Class A High Current Design Power Amp without RELAY built inside.

- 45W output per Channel.

- It has two transformer inside for due channels operation.

- The DR-3 VHC in now running in STEREO mode and it can be set as a MONO BLOCK for operation. If setting as mono block, you need two for stereo setup.

- Its weight is about 45 Kg.

Please contact me via PM for whom is serious and interested to them. Thank you.

*** Some extra spare parts in NEW, such as Philips 4700u 40V capacitors and power switch of DR-7 power supply, will be given for free as gift for back up and long term maintenance to someone take the whole set as one go without bargain.

Following photos are for your reference only:

https://farm1.staticflickr.com/922/43099959001_271f093af7_b.jpg

https://farm2.staticflickr.com/1763/41299277780_3351526247_b.jpg

https://farm1.staticflickr.com/919/43439741681_8faae1a6b9_b.jpg

https://farm2.staticflickr.com/1770/29227476618_50a046411f_b.jpg

https://farm1.staticflickr.com/842/41288602240_88ab81b591_b.jpg

* Note: There are 6 original large capacitors, in RED color, under the green main board inside the power supply.

https://farm1.staticflickr.com/837/43099960251_6241a68eb2_b.jpg

https://farm2.staticflickr.com/1827/29227478508_ce9b37c15b_b.jpg


wlhuen
個人訊息 會員
138.xxx.xxx.142
2019-05-05 23:53
[#6] 出售:Classe DR-7 Pre-Amp & DR-3 VHC Power Amp 220V    
價錢 HK$: 48000

HK$: 48000 for both units as one set

A set of RARE Classe flagship Pre-Amp and Power Amp, DR-7 and DR-3 VHC both in 220V setting, is listed for sale. They are the top models in this GOLDEN HANDLE DR series designed by the Classe co-founder, Dave Reich, in the golden age of vinyl and really RARE in the market.

The DR-7 Pre-Amp and DR-3 VHC Power Amp are in 100% excellent working condition without any problem. The cosmetic condition of the DR-7 is about 90% new and the DR-3 VHC is about 85% new, conservatively speaking.

Both units are 100% original without modification except

1> The rubber feet of the DR-3 VHC have been replaced with the bigger ones for better support due to the weight.
2> The power switch of the power supply in the DR-7 was replaced with an original parts as it was broken due to age.

The power supply of the DR-7 had original voltage setting as 120V but it has been changed to support 220V now by reshuffling the internal transformer wiring inside the power supply itself, so both units are now running in 220V voltage and NO external step down transformer is required any more.

Please also find the following product information as reference:

The DR-7 Pre-Amp

- 2 Phono input, PHONO1 and PHONO2, both support MM and MC.

- For MC phono input, it is supported the MC HEADAMP boards, NIL-3, inside which is SELF-ADJUSTING the Input Impedance with factory set the nominal gain of 27 dB, and the gain can be adjusted by using the resistor in different ohm value.

- For MM phono input, it supports the following different Impedance and Capacitance:

3, 5 ,10, 47, 100, 470, 10k, 33k, 47k, 100k ohm and SPARE
47, 100, 150, 220, 330 and 470 pf.

- 5 Line Inputs, CD, TUNER, AUX, TAPE1 and TAPE2

- 2 Line Outputs, TAPE1 and TAPE2 as well as 2 Main Outputs, MAIN 1 and 2.

- The CD input as 2 different modes to operate, FILTERED and DIRECT, where it has 5 filters dip switches to attenuate the high frequency response of CD players.

- It has STAR GROUNDING Bus Bar to prevent ground loops and reduce the noise floor.

- It has separate power supply with Swiss Lemo Fischer termination at both side by connecting with an original factory made cable with Fischer connectors. 5 individual transformers are used inside the power supply for supporting different function/operation of the DR-7 Pre-Amp.

- Its weight is about 25 Kg.

- A copy of user manual is included.

The DR-3 VHC Power Amp

- It is a PURE Class A High Current Design Power Amp without RELAY built inside.

- 45W output per Channel.

- It has two transformer inside for due channels operation.

- The DR-3 VHC in now running in STEREO mode and it can be set as a MONO BLOCK for operation. If setting as mono block, you need two for stereo setup.

- Its weight is about 45 Kg.

Please contact me via PM for whom is serious and interested to them. Thank you.

*** Some extra spare parts in NEW, such as Philips 4700u 40V capacitors and power switch of DR-7 power supply, will be given for free as gift for back up and long term maintenance to someone take the whole set as one go without bargain.

Following photos are for your reference only:

https://farm1.staticflickr.com/922/43099959001_271f093af7_b.jpg

https://farm2.staticflickr.com/1763/41299277780_3351526247_b.jpg

https://farm1.staticflickr.com/919/43439741681_8faae1a6b9_b.jpg

https://farm2.staticflickr.com/1770/29227476618_50a046411f_b.jpg

https://farm1.staticflickr.com/842/41288602240_88ab81b591_b.jpg

* Note: There are 6 original large capacitors, in RED color, under the green main board inside the power supply.

https://farm1.staticflickr.com/837/43099960251_6241a68eb2_b.jpg

https://farm2.staticflickr.com/1827/29227478508_ce9b37c15b_b.jpg




最後修改時間: 2019-07-06 23:48:04
wlhuen
個人訊息 會員
138.xxx.xxx.142
2019-07-06 23:43
[#7] 出售:Classe DR-7 Pre-Amp & DR-3 VHC Power Amp 220V    
價錢 HK$: 48000

HK$: 48000 for both units as one set

A set of RARE Classe flagship Pre-Amp and Power Amp, DR-7 and DR-3 VHC both in 220V setting, is listed for sale. They are the top models in this GOLDEN HANDLE DR series designed by the Classe co-founder, Dave Reich, in the golden age of vinyl and really RARE in the market.

The DR-7 Pre-Amp and DR-3 VHC Power Amp are in 100% excellent working condition without any problem. The cosmetic condition of the DR-7 is about 90% new and the DR-3 VHC is about 85% new, conservatively speaking.

Both units are 100% original without modification except

1> The rubber feet of the DR-3 VHC have been replaced with the bigger ones for better support due to the weight.
2> The power switch of the power supply in the DR-7 was replaced with an original parts as it was broken due to age.

The power supply of the DR-7 had original voltage setting as 120V but it has been changed to support 220V now by reshuffling the internal transformer wiring inside the power supply itself, so both units are now running in 220V voltage and NO external step down transformer is required any more.

This set is now being used to drive my JBL 4315, doing a very good job, good match for vintage JBL speakers.

Please also find the following product information as reference:

The DR-7 Pre-Amp

- 2 Phono input, PHONO1 and PHONO2, both support MM and MC.

- For MC phono input, it is supported the MC HEADAMP boards, NIL-3, inside which is SELF-ADJUSTING the Input Impedance with factory set the nominal gain of 27 dB, and the gain can be adjusted by using the resistor in different ohm value.

- For MM phono input, it supports the following different Impedance and Capacitance:

3, 5 ,10, 47, 100, 470, 10k, 33k, 47k, 100k ohm and SPARE
47, 100, 150, 220, 330 and 470 pf.

- 5 Line Inputs, CD, TUNER, AUX, TAPE1 and TAPE2

- 2 Line Outputs, TAPE1 and TAPE2 as well as 2 Main Outputs, MAIN 1 and 2.

- The CD input as 2 different modes to operate, FILTERED and DIRECT, where it has 5 filters dip switches to attenuate the high frequency response of CD players.

- It has STAR GROUNDING Bus Bar to prevent ground loops and reduce the noise floor.

- It has separate power supply with Swiss Lemo Fischer termination at both side by connecting with an original factory made cable with Fischer connectors. 5 individual transformers are used inside the power supply for supporting different function/operation of the DR-7 Pre-Amp.

- Its weight is about 25 Kg.

- A copy of user manual is included.

The DR-3 VHC Power Amp

- It is a PURE Class A High Current Design Power Amp without RELAY built inside.

- 45W output per Channel.

- It has two transformer inside for due channels operation.

- The DR-3 VHC in now running in STEREO mode and it can be set as a MONO BLOCK for operation. If setting as mono block, you need two for stereo setup.

- Its weight is about 45 Kg.

Please contact me via PM for whom is serious and interested to them. Thank you.

*** Some extra spare parts in NEW, such as Philips 4700u 40V capacitors and power switch of DR-7 power supply, will be given for free as gift for back up and long term maintenance to someone take the whole set as one go without bargain.

Following photos are for your reference only:

https://farm1.staticflickr.com/922/43099959001_271f093af7_b.jpg

https://farm2.staticflickr.com/1763/41299277780_3351526247_b.jpg

https://farm1.staticflickr.com/919/43439741681_8faae1a6b9_b.jpg

https://farm2.staticflickr.com/1770/29227476618_50a046411f_b.jpg

https://farm1.staticflickr.com/842/41288602240_88ab81b591_b.jpg

* Note: There are 6 original large capacitors, in RED color, under the green main board inside the power supply.

https://farm1.staticflickr.com/837/43099960251_6241a68eb2_b.jpg

https://farm2.staticflickr.com/1827/29227478508_ce9b37c15b_b.jpg


wlhuen
個人訊息 會員
138.xxx.xxx.142
2019-09-23 23:58
[#8] 出售:Classe DR-7 Pre-Amp & DR-3 VHC Power Amp 220V    
價錢 HK$: 46,800

HK$: 46,800 for both units as one set

A set of RARE Classe flagship Pre-Amp and Power Amp, DR-7 and DR-3 VHC both in 220V setting, is listed for sale. They are the top models in this GOLDEN HANDLE DR series designed by the Classe co-founder, Dave Reich, in the golden age of vinyl and really RARE in the market.

The DR-7 Pre-Amp and DR-3 VHC Power Amp are in 100% excellent working condition without any problem. The cosmetic condition of the DR-7 is about 90% new and the DR-3 VHC is about 85% new, conservatively speaking.

Both units are 100% original without modification except

1> The rubber feet of the DR-3 VHC have been replaced with the bigger ones for better support due to the weight.
2> The power switch of the power supply in the DR-7 was replaced with an original parts as it was broken due to age.

The power supply of the DR-7 had original voltage setting as 120V but it has been changed to support 220V now by reshuffling the internal transformer wiring inside the power supply itself, so both units are now running in 220V voltage and NO external step down transformer is required any more.

This set is now being used to drive my JBL 4315, doing a very good job, good match for vintage JBL speakers.

Please also find the following product information as reference:

The DR-7 Pre-Amp

- 2 Phono input, PHONO1 and PHONO2, both support MM and MC.

- For MC phono input, it is supported the MC HEADAMP boards, NIL-3, inside which is SELF-ADJUSTING the Input Impedance with factory set the nominal gain of 27 dB, and the gain can be adjusted by using the resistor in different ohm value.

- For MM phono input, it supports the following different Impedance and Capacitance:

3, 5 ,10, 47, 100, 470, 10k, 33k, 47k, 100k ohm and SPARE
47, 100, 150, 220, 330 and 470 pf.

- 5 Line Inputs, CD, TUNER, AUX, TAPE1 and TAPE2

- 2 Line Outputs, TAPE1 and TAPE2 as well as 2 Main Outputs, MAIN 1 and 2.

- The CD input as 2 different modes to operate, FILTERED and DIRECT, where it has 5 filters dip switches to attenuate the high frequency response of CD players.

- It has STAR GROUNDING Bus Bar to prevent ground loops and reduce the noise floor.

- It has separate power supply with Swiss Lemo Fischer termination at both side by connecting with an original factory made cable with Fischer connectors. 5 individual transformers are used inside the power supply for supporting different function/operation of the DR-7 Pre-Amp.

- Its weight is about 25 Kg.

- A copy of user manual is included.

The DR-3 VHC Power Amp

- It is a PURE Class A High Current Design Power Amp without RELAY built inside.

- 45W output per Channel.

- It has two transformer inside for due channels operation.

- The DR-3 VHC in now running in STEREO mode and it can be set as a MONO BLOCK for operation. If setting as mono block, you need two for stereo setup.

- Its weight is about 45 Kg.

Please contact me via PM for whom is serious and interested to them. Thank you.

*** Some extra spare parts in NEW, such as Philips 4700u 40V capacitors and power switch of DR-7 power supply, will be given for free as gift for back up and long term maintenance to someone take the whole set as one go without bargain.

Following photos are for your reference only:

https://farm1.staticflickr.com/922/43099959001_271f093af7_b.jpg

https://farm2.staticflickr.com/1763/41299277780_3351526247_b.jpg

https://farm1.staticflickr.com/919/43439741681_8faae1a6b9_b.jpg

https://farm2.staticflickr.com/1770/29227476618_50a046411f_b.jpg

https://farm1.staticflickr.com/842/41288602240_88ab81b591_b.jpg

* Note: There are 6 original large capacitors, in RED color, under the green main board inside the power supply of the DR-7 preamp.

https://farm1.staticflickr.com/837/43099960251_6241a68eb2_b.jpg

https://farm2.staticflickr.com/1827/29227478508_ce9b37c15b_b.jpg

**** NOTE: As a special to the buyer got the whole set, an extra set of 8 ORIGINAL RED CAPACITORS as spare parts for the DR-3 VHC, they are the two columns of RED capacitors shown in the right and left sides of the DR-3 VHC via the link above. But, they are not available on hand at this moment, need to got them from its home from Canada months later. However, there original inside the DR-3 VHC now are still in excellent working condition, having this extra set would let this DR-3 VHC has another long years service in your system.



wlhuen
個人訊息 會員
138.xxx.xxx.142
2019-12-30 23:44
[#9] 出售:Classe DR-7 Pre-Amp & DR-3 VHC Power Amp 220V    
價錢 HK$: 46,800

HK$: 46,800 for both units as one set

A set of RARE Classe flagship Pre-Amp and Power Amp, DR-7 and DR-3 VHC both in 220V setting, is listed for sale. They are the top models in this GOLDEN HANDLE DR series designed by the Classe co-founder, Dave Reich, in the golden age of vinyl and really RARE in the market.

The DR-7 Pre-Amp and DR-3 VHC Power Amp are in 100% excellent working condition without any problem. The cosmetic condition of the DR-7 is about 90% new and the DR-3 VHC is about 85% new, conservatively speaking.

Both units are 100% original without modification except

1> The rubber feet of the DR-3 VHC have been replaced with the bigger ones for better support due to the weight.
2> The power switch of the power supply in the DR-7 was replaced with an original parts as it was broken due to age.

The power supply of the DR-7 had original voltage setting as 120V but it has been changed to support 220V now by reshuffling the internal transformer wiring inside the power supply itself, so both units are now running in 220V voltage and NO external step down transformer is required any more.

This set is now being used to drive my JBL 4315, doing a very good job, good match for vintage JBL speakers.

Please also find the following product information as reference:

The DR-7 Pre-Amp

- 2 Phono input, PHONO1 and PHONO2, both support MM and MC.

- For MC phono input, it is supported the MC HEADAMP boards, NIL-3, inside which is SELF-ADJUSTING the Input Impedance with factory set the nominal gain of 27 dB, and the gain can be adjusted by using the resistor in different ohm value.

- For MM phono input, it supports the following different Impedance and Capacitance:

3, 5 ,10, 47, 100, 470, 10k, 33k, 47k, 100k ohm and SPARE
47, 100, 150, 220, 330 and 470 pf.

- 5 Line Inputs, CD, TUNER, AUX, TAPE1 and TAPE2

- 2 Line Outputs, TAPE1 and TAPE2 as well as 2 Main Outputs, MAIN 1 and 2.

- The CD input as 2 different modes to operate, FILTERED and DIRECT, where it has 5 filters dip switches to attenuate the high frequency response of CD players.

- It has STAR GROUNDING Bus Bar to prevent ground loops and reduce the noise floor.

- It has separate power supply with Swiss Lemo Fischer termination at both side by connecting with an original factory made cable with Fischer connectors. 5 individual transformers are used inside the power supply for supporting different function/operation of the DR-7 Pre-Amp.

- Its weight is about 25 Kg.

- A copy of user manual is included.

The DR-3 VHC Power Amp

- It is a PURE Class A High Current Design Power Amp without RELAY built inside.

- 45W output per Channel.

- It has two transformer inside for due channels operation.

- The DR-3 VHC in now running in STEREO mode and it can be set as a MONO BLOCK for operation. If setting as mono block, you need two for stereo setup.

- Its weight is about 45 Kg.

Please contact me via PM for whom is serious and interested to them. Thank you.

*** Some extra spare parts in NEW, such as Philips 4700u 40V capacitors and power switch of DR-7 power supply, will be given for free as gift for back up and long term maintenance to someone take the whole set as one go without bargain.

Following photos are for your reference only:

https://farm1.staticflickr.com/922/43099959001_271f093af7_b.jpg

https://farm2.staticflickr.com/1763/41299277780_3351526247_b.jpg

https://farm1.staticflickr.com/919/43439741681_8faae1a6b9_b.jpg

https://farm2.staticflickr.com/1770/29227476618_50a046411f_b.jpg

https://farm1.staticflickr.com/842/41288602240_88ab81b591_b.jpg

* Note: There are 6 original large capacitors, in RED color, under the green main board inside the power supply of the DR-7 preamp.

https://farm1.staticflickr.com/837/43099960251_6241a68eb2_b.jpg

https://farm2.staticflickr.com/1827/29227478508_ce9b37c15b_b.jpg



wlhuen
個人訊息 會員
138.xxx.xxx.142
2020-02-17 23:42
[#10] 出售:Classe DR-7 Pre-Amp & DR-3 VHC Power Amp 220V    
價錢 HK$: 46,800

HK$: 46,800 for both units as one set

A set of RARE Classe flagship Pre-Amp and Power Amp, DR-7 and DR-3 VHC both in 220V setting, is listed for sale. They are the top models in this GOLDEN HANDLE DR series designed by the Classe co-founder, Dave Reich, in the golden age of vinyl and really RARE in the market.

The DR-7 Pre-Amp and DR-3 VHC Power Amp are in 100% excellent working condition without any problem. The cosmetic condition of the DR-7 is about 90% new and the DR-3 VHC is about 85% new, conservatively speaking.

Both units are 100% original without modification except

1> The rubber feet of the DR-3 VHC have been replaced with the bigger ones for better support due to the weight.
2> The power switch of the power supply in the DR-7 was replaced with an original parts as it was broken due to age.

The power supply of the DR-7 had original voltage setting as 120V but it has been changed to support 220V now by reshuffling the internal transformer wiring inside the power supply itself, so both units are now running in 220V voltage and NO external step down transformer is required any more.

This set is now being used to drive my JBL 4315, doing a very good job, good match for vintage JBL speakers.

Please also find the following product information as reference:

The DR-7 Pre-Amp

- 2 Phono input, PHONO1 and PHONO2, both support MM and MC.

- For MC phono input, it is supported the MC HEADAMP boards, NIL-3, inside which is SELF-ADJUSTING the Input Impedance with factory set the nominal gain of 27 dB, and the gain can be adjusted by using the resistor in different ohm value.

- For MM phono input, it supports the following different Impedance and Capacitance:

3, 5 ,10, 47, 100, 470, 10k, 33k, 47k, 100k ohm and SPARE
47, 100, 150, 220, 330 and 470 pf.

- 5 Line Inputs, CD, TUNER, AUX, TAPE1 and TAPE2

- 2 Line Outputs, TAPE1 and TAPE2 as well as 2 Main Outputs, MAIN 1 and 2.

- The CD input as 2 different modes to operate, FILTERED and DIRECT, where it has 5 filters dip switches to attenuate the high frequency response of CD players.

- It has STAR GROUNDING Bus Bar to prevent ground loops and reduce the noise floor.

- It has separate power supply with Swiss Lemo Fischer termination at both side by connecting with an original factory made cable with Fischer connectors. 5 individual transformers are used inside the power supply for supporting different function/operation of the DR-7 Pre-Amp.

- Its weight is about 25 Kg.

- A copy of user manual is included.

The DR-3 VHC Power Amp

- It is a PURE Class A High Current Design Power Amp without RELAY built inside.

- 45W output per Channel.

- It has two transformer inside for due channels operation.

- The DR-3 VHC in now running in STEREO mode and it can be set as a MONO BLOCK for operation. If setting as mono block, you need two for stereo setup.

- Its weight is about 45 Kg.

Please contact me via PM for whom is serious and interested to them. Thank you.

*** Some extra spare parts in NEW, such as Philips 4700u 40V capacitors and power switch of DR-7 power supply, will be given for free as gift for back up and long term maintenance to someone take the whole set as one go without bargain.

Following photos are for your reference only:

https://farm1.staticflickr.com/922/43099959001_271f093af7_b.jpg

https://farm2.staticflickr.com/1763/41299277780_3351526247_b.jpg

https://farm1.staticflickr.com/919/43439741681_8faae1a6b9_b.jpg

https://farm2.staticflickr.com/1770/29227476618_50a046411f_b.jpg

https://farm1.staticflickr.com/842/41288602240_88ab81b591_b.jpg

* Note: There are 6 original large capacitors, in RED color, under the green main board inside the power supply of the DR-7 preamp.

https://farm1.staticflickr.com/837/43099960251_6241a68eb2_b.jpg

https://farm2.staticflickr.com/1827/29227478508_ce9b37c15b_b.jpg


wlhuen
個人訊息 會員
138.xxx.xxx.142
2020-02-29 11:25
[#11] 出售:Classe DR-7 Pre-Amp & DR-3 VHC Power Amp 220V    
價錢 HK$: 46,800

HK$: 46,800 for both units as one set

A set of RARE Classe flagship Pre-Amp and Power Amp, DR-7 and DR-3 VHC both in 220V setting, is listed for sale. They are the top models in this GOLDEN HANDLE DR series designed by the Classe co-founder, Dave Reich, in the golden age of vinyl and really RARE in the market.

The DR-7 Pre-Amp and DR-3 VHC Power Amp are in 100% excellent working condition without any problem. The cosmetic condition of the DR-7 is about 90% new and the DR-3 VHC is about 85% new, conservatively speaking.

Both units are 100% original without modification except

1> The rubber feet of the DR-3 VHC have been replaced with the bigger ones for better support due to the weight.
2> The power switch of the power supply in the DR-7 was replaced with an original parts as it was broken due to age.

The power supply of the DR-7 had original voltage setting as 120V but it has been changed to support 220V now by reshuffling the internal transformer wiring inside the power supply itself, so both units are now running in 220V voltage and NO external step down transformer is required any more.

This set is now being used to drive my JBL 4315, doing a very good job, good match for vintage JBL speakers.

Please also find the following product information as reference:

The DR-7 Pre-Amp

- 2 Phono input, PHONO1 and PHONO2, both support MM and MC.

- For MC phono input, it is supported the MC HEADAMP boards, NIL-3, inside which is SELF-ADJUSTING the Input Impedance with factory set the nominal gain of 27 dB, and the gain can be adjusted by using the resistor in different ohm value.

- For MM phono input, it supports the following different Impedance and Capacitance:

3, 5 ,10, 47, 100, 470, 10k, 33k, 47k, 100k ohm and SPARE
47, 100, 150, 220, 330 and 470 pf.

- 5 Line Inputs, CD, TUNER, AUX, TAPE1 and TAPE2

- 2 Line Outputs, TAPE1 and TAPE2 as well as 2 Main Outputs, MAIN 1 and 2.

- The CD input as 2 different modes to operate, FILTERED and DIRECT, where it has 5 filters dip switches to attenuate the high frequency response of CD players.

- It has STAR GROUNDING Bus Bar to prevent ground loops and reduce the noise floor.

- It has separate power supply with Swiss Lemo Fischer termination at both side by connecting with an original factory made cable with Fischer connectors. 5 individual transformers are used inside the power supply for supporting different function/operation of the DR-7 Pre-Amp.

- Its weight is about 25 Kg.

- A copy of user manual is included.

The DR-3 VHC Power Amp

- It is a PURE Class A High Current Design Power Amp without RELAY built inside.

- 45W output per Channel.

- It has two transformer inside for due channels operation.

- The DR-3 VHC in now running in STEREO mode and it can be set as a MONO BLOCK for operation. If setting as mono block, you need two for stereo setup.

- Its weight is about 45 Kg.

Please contact me via PM for whom is serious and interested to them. Thank you.

*** Some extra spare parts in NEW, such as Philips 4700u 40V capacitors and power switch of DR-7 power supply, will be given for free as gift for back up and long term maintenance to someone take the whole set as one go without bargain.

Following photos are for your reference only:

https://farm1.staticflickr.com/922/43099959001_271f093af7_b.jpg

https://farm2.staticflickr.com/1763/41299277780_3351526247_b.jpg

https://farm1.staticflickr.com/919/43439741681_8faae1a6b9_b.jpg

https://farm2.staticflickr.com/1770/29227476618_50a046411f_b.jpg

https://farm1.staticflickr.com/842/41288602240_88ab81b591_b.jpg

* Note: There are 6 original large capacitors, in RED color, under the green main board inside the power supply of the DR-7 preamp.

https://farm1.staticflickr.com/837/43099960251_6241a68eb2_b.jpg

https://farm2.staticflickr.com/1827/29227478508_ce9b37c15b_b.jpg


wlhuen
個人訊息 會員
138.xxx.xxx.142
2020-05-21 00:08
[#12] 出售:Classe DR-7 Pre-Amp & DR-3 VHC Power Amp 220V    
師兄,可否浄consider dr7?
beeboy
個人訊息 會員
58.xxx.xxx.46
2020-06-21 16:45
[#13] 出售:Classe DR-7 Pre-Amp & DR-3 VHC Power Amp 220V    
Beeboy hing,

Please check PM.

Thank you.
wlhuen
個人訊息 會員
138.xxx.xxx.142
2020-06-22 11:49
[#14] 出售:Classe DR-7 Pre-Amp & DR-3 VHC Power Amp 220V    
價錢 HK$: 46,800

HK$: 46,800 for both units as one set, separate sale is also welcome to further discuss.

A set of RARE Classe flagship Pre-Amp and Power Amp, DR-7 and DR-3 VHC both in 220V setting, is listed for sale. They are the top models in this GOLDEN HANDLE DR series designed by the Classe co-founder, Dave Reich, in the golden age of vinyl and really RARE in the market.

The DR-7 Pre-Amp and DR-3 VHC Power Amp are in 100% excellent working condition without any problem. The cosmetic condition of the DR-7 is about 90% new and the DR-3 VHC is about 85% new, conservatively speaking.

Both units are 100% original without modification except

1> The rubber feet of the DR-3 VHC have been replaced with the bigger ones for better support due to the weight.
2> The power switch of the power supply in the DR-7 was replaced with an original parts as it was broken due to age.

The power supply of the DR-7 had original voltage setting as 120V but it has been changed to support 220V now by reshuffling the internal transformer wiring inside the power supply itself, so both units are now running in 220V voltage and NO external step down transformer is required any more.

This set is now being used to drive my JBL 4315, doing a very good job, good match for vintage JBL speakers.

Please also find the following product information as reference:

The DR-7 Pre-Amp

- 2 Phono input, PHONO1 and PHONO2, both support MM and MC.

- For MC phono input, it is supported the MC HEADAMP boards, NIL-3, inside which is SELF-ADJUSTING the Input Impedance with factory set the nominal gain of 27 dB, and the gain can be adjusted by using the resistor in different ohm value.

- For MM phono input, it supports the following different Impedance and Capacitance:

3, 5 ,10, 47, 100, 470, 10k, 33k, 47k, 100k ohm and SPARE
47, 100, 150, 220, 330 and 470 pf.

- 5 Line Inputs, CD, TUNER, AUX, TAPE1 and TAPE2

- 2 Line Outputs, TAPE1 and TAPE2 as well as 2 Main Outputs, MAIN 1 and 2.

- The CD input as 2 different modes to operate, FILTERED and DIRECT, where it has 5 filters dip switches to attenuate the high frequency response of CD players.

- It has STAR GROUNDING Bus Bar to prevent ground loops and reduce the noise floor.

- It has separate power supply with Swiss Lemo Fischer termination at both side by connecting with an original factory made cable with Fischer connectors. 5 individual transformers are used inside the power supply for supporting different function/operation of the DR-7 Pre-Amp.

- Its weight is about 25 Kg.

- A copy of user manual is included.

The DR-3 VHC Power Amp

- It is a PURE Class A High Current Design Power Amp without RELAY built inside.

- 45W output per Channel.

- It has two transformer inside for due channels operation.

- The DR-3 VHC in now running in STEREO mode and it can be set as a MONO BLOCK for operation. If setting as mono block, you need two for stereo setup.

- Its weight is about 45 Kg.

Please contact me via PM for whom is serious and interested to them. Thank you.

*** Some extra spare parts in NEW, such as Philips 4700u 40V capacitors and power switch of DR-7 power supply, will be given for free as gift for back up and long term maintenance to someone take the whole set as one go without bargain.

Following photos are for your reference only:

https://farm1.staticflickr.com/922/43099959001_271f093af7_b.jpg

https://farm2.staticflickr.com/1763/41299277780_3351526247_b.jpg

https://farm1.staticflickr.com/919/43439741681_8faae1a6b9_b.jpg

https://farm2.staticflickr.com/1770/29227476618_50a046411f_b.jpg

https://farm1.staticflickr.com/842/41288602240_88ab81b591_b.jpg

* Note: There are 6 original large capacitors, in RED color, under the green main board inside the power supply of the DR-7 preamp.

https://farm1.staticflickr.com/837/43099960251_6241a68eb2_b.jpg

https://farm2.staticflickr.com/1827/29227478508_ce9b37c15b_b.jpg


wlhuen
個人訊息 會員
138.xxx.xxx.142
2020-08-10 00:21
[#15] 出售:Classe DR-7 Pre-Amp & DR-3 VHC Power Amp 220V    
價錢 HK$: 46,800

HK$: 46,800 for both units as one set, separate sale is also welcome to further discuss.

A set of RARE Classe flagship Pre-Amp and Power Amp, DR-7 and DR-3 VHC both in 220V setting, is listed for sale. They are the top models in this GOLDEN HANDLE DR series designed by the Classe co-founder, Dave Reich, in the golden age of vinyl and really RARE in the market.

The DR-7 Pre-Amp and DR-3 VHC Power Amp are in 100% excellent working condition without any problem. The cosmetic condition of the DR-7 is about 90% new and the DR-3 VHC is about 85% new, conservatively speaking.

Both units are 100% original without modification except

1> The rubber feet of the DR-3 VHC have been replaced with the bigger ones for better support due to the weight.
2> The power switch of the power supply in the DR-7 was replaced with an original parts as it was broken due to age.

The power supply of the DR-7 had original voltage setting as 120V but it has been changed to support 220V now by reshuffling the internal transformer wiring inside the power supply itself, so both units are now running in 220V voltage and NO external step down transformer is required any more.

This set is now being used to drive my JBL 4315, doing a very good job, good match for vintage JBL speakers.

Please also find the following product information as reference:

The DR-7 Pre-Amp

- 2 Phono input, PHONO1 and PHONO2, both support MM and MC.

- For MC phono input, it is supported the MC HEADAMP boards, NIL-3, inside which is SELF-ADJUSTING the Input Impedance with factory set the nominal gain of 27 dB, and the gain can be adjusted by using the resistor in different ohm value.

- For MM phono input, it supports the following different Impedance and Capacitance:

3, 5 ,10, 47, 100, 470, 10k, 33k, 47k, 100k ohm and SPARE
47, 100, 150, 220, 330 and 470 pf.

- 5 Line Inputs, CD, TUNER, AUX, TAPE1 and TAPE2

- 2 Line Outputs, TAPE1 and TAPE2 as well as 2 Main Outputs, MAIN 1 and 2.

- The CD input as 2 different modes to operate, FILTERED and DIRECT, where it has 5 filters dip switches to attenuate the high frequency response of CD players.

- It has STAR GROUNDING Bus Bar to prevent ground loops and reduce the noise floor.

- It has separate power supply with Swiss Lemo Fischer termination at both side by connecting with an original factory made cable with Fischer connectors. 5 individual transformers are used inside the power supply for supporting different function/operation of the DR-7 Pre-Amp.

- Its weight is about 25 Kg.

- A copy of user manual is included.

The DR-3 VHC Power Amp

- It is a PURE Class A High Current Design Power Amp without RELAY built inside.

- 45W output per Channel.

- It has two transformer inside for due channels operation.

- The DR-3 VHC in now running in STEREO mode and it can be set as a MONO BLOCK for operation. If setting as mono block, you need two for stereo setup.

- Its weight is about 45 Kg.

Please contact me via PM for whom is serious and interested to them. Thank you.

*** Some extra spare parts in NEW, such as Philips 4700u 40V capacitors and power switch of DR-7 power supply, will be given for free as gift for back up and long term maintenance to someone take the whole set as one go without bargain.

Following photos are for your reference only:

https://farm1.staticflickr.com/922/43099959001_271f093af7_b.jpg

https://farm2.staticflickr.com/1763/41299277780_3351526247_b.jpg

https://farm1.staticflickr.com/919/43439741681_8faae1a6b9_b.jpg

https://farm2.staticflickr.com/1770/29227476618_50a046411f_b.jpg

https://farm1.staticflickr.com/842/41288602240_88ab81b591_b.jpg

* Note: There are 6 original large capacitors, in RED color, under the green main board inside the power supply of the DR-7 preamp.

https://farm1.staticflickr.com/837/43099960251_6241a68eb2_b.jpg

https://farm2.staticflickr.com/1827/29227478508_ce9b37c15b_b.jpg


wlhuen
個人訊息 會員
138.xxx.xxx.142
2020-09-16 23:25
[#16] 出售:Classe DR-7 Pre-Amp & DR-3 VHC Power Amp 220V    
價錢 HK$: 44,800

HK$: 46,800 for both units as one set, separate sale is also welcome to further discuss.

A set of RARE Classe flagship Pre-Amp and Power Amp, DR-7 and DR-3 VHC both in 220V setting, is listed for sale. They are the top models in this GOLDEN HANDLE DR series designed by the Classe co-founder, Dave Reich, in the golden age of vinyl and really RARE in the market.

The DR-7 Pre-Amp and DR-3 VHC Power Amp are in 100% excellent working condition without any problem. The cosmetic condition of the DR-7 is about 90% new and the DR-3 VHC is about 85% new, conservatively speaking.

Both units are 100% original without modification except

1> The rubber feet of the DR-3 VHC have been replaced with the bigger ones for better support due to the weight.
2> The power switch of the power supply in the DR-7 was replaced with an original parts as it was broken due to age.

The power supply of the DR-7 had original voltage setting as 120V but it has been changed to support 220V now by reshuffling the internal transformer wiring inside the power supply itself, so both units are now running in 220V voltage and NO external step down transformer is required any more.

This set is now being used to drive my JBL 4315, doing a very good job, good match for vintage JBL speakers.

Please also find the following product information as reference:

The DR-7 Pre-Amp

- 2 Phono input, PHONO1 and PHONO2, both support MM and MC.

- For MC phono input, it is supported the MC HEADAMP boards, NIL-3, inside which is SELF-ADJUSTING the Input Impedance with factory set the nominal gain of 27 dB, and the gain can be adjusted by using the resistor in different ohm value.

- For MM phono input, it supports the following different Impedance and Capacitance:

3, 5 ,10, 47, 100, 470, 10k, 33k, 47k, 100k ohm and SPARE
47, 100, 150, 220, 330 and 470 pf.

- 5 Line Inputs, CD, TUNER, AUX, TAPE1 and TAPE2

- 2 Line Outputs, TAPE1 and TAPE2 as well as 2 Main Outputs, MAIN 1 and 2.

- The CD input as 2 different modes to operate, FILTERED and DIRECT, where it has 5 filters dip switches to attenuate the high frequency response of CD players.

- It has STAR GROUNDING Bus Bar to prevent ground loops and reduce the noise floor.

- It has separate power supply with Swiss Lemo Fischer termination at both side by connecting with an original factory made cable with Fischer connectors. 5 individual transformers are used inside the power supply for supporting different function/operation of the DR-7 Pre-Amp.

- Its weight is about 25 Kg.

- A copy of user manual is included.

The DR-3 VHC Power Amp

- It is a PURE Class A High Current Design Power Amp without RELAY built inside.

- 45W output per Channel.

- It has two transformer inside for due channels operation.

- The DR-3 VHC in now running in STEREO mode and it can be set as a MONO BLOCK for operation. If setting as mono block, you need two for stereo setup.

- Its weight is about 45 Kg.

Please contact me via PM for whom is serious and interested to them. Thank you.

*** Some extra spare parts in NEW, such as Philips 4700u 40V capacitors and power switch of DR-7 power supply, will be given for free as gift for back up and long term maintenance to someone take the whole set as one go without bargain.

Following photos are for your reference only:

https://farm1.staticflickr.com/922/43099959001_271f093af7_b.jpg

https://farm2.staticflickr.com/1763/41299277780_3351526247_b.jpg

https://farm1.staticflickr.com/919/43439741681_8faae1a6b9_b.jpg

https://farm2.staticflickr.com/1770/29227476618_50a046411f_b.jpg

https://farm1.staticflickr.com/842/41288602240_88ab81b591_b.jpg

* Note: There are 6 original large capacitors, in RED color, under the green main board inside the power supply of the DR-7 preamp.

https://farm1.staticflickr.com/837/43099960251_6241a68eb2_b.jpg

https://farm2.staticflickr.com/1827/29227478508_ce9b37c15b_b.jpg


wlhuen
個人訊息 會員
138.xxx.xxx.142
2020-12-16 23:33
[#17] 出售:Classe DR-7 Pre-Amp & DR-3 VHC Power Amp 220V    
價錢 HK$: 46,800

HK$: 46,800 for both units as one set, separate sale is also welcome to further discuss.

A set of RARE Classe flagship Pre-Amp and Power Amp, DR-7 and DR-3 VHC both in 220V setting, is listed for sale. They are the top models in this GOLDEN HANDLE DR series designed by the Classe co-founder, Dave Reich, in the golden age of vinyl and really RARE in the market.

The DR-7 Pre-Amp and DR-3 VHC Power Amp are in 100% excellent working condition without any problem. The cosmetic condition of the DR-7 is about 90% new and the DR-3 VHC is about 85% new, conservatively speaking.

Both units are 100% original without modification except

1> The rubber feet of the DR-3 VHC have been replaced with the bigger ones for better support due to the weight.
2> The power switch of the power supply in the DR-7 was replaced with an original parts as it was broken due to age.

The power supply of the DR-7 had original voltage setting as 120V but it has been changed to support 220V now by reshuffling the internal transformer wiring inside the power supply itself, so both units are now running in 220V voltage and NO external step down transformer is required any more.

This set is now being used to drive my JBL 4315, doing a very good job, good match for vintage JBL speakers.

Please also find the following product information as reference:

The DR-7 Pre-Amp

- 2 Phono input, PHONO1 and PHONO2, both support MM and MC.

- For MC phono input, it is supported the MC HEADAMP boards, NIL-3, inside which is SELF-ADJUSTING the Input Impedance with factory set the nominal gain of 27 dB, and the gain can be adjusted by using the resistor in different ohm value.

- For MM phono input, it supports the following different Impedance and Capacitance:

3, 5 ,10, 47, 100, 470, 10k, 33k, 47k, 100k ohm and SPARE
47, 100, 150, 220, 330 and 470 pf.

- 5 Line Inputs, CD, TUNER, AUX, TAPE1 and TAPE2

- 2 Line Outputs, TAPE1 and TAPE2 as well as 2 Main Outputs, MAIN 1 and 2.

- The CD input as 2 different modes to operate, FILTERED and DIRECT, where it has 5 filters dip switches to attenuate the high frequency response of CD players.

- It has STAR GROUNDING Bus Bar to prevent ground loops and reduce the noise floor.

- It has separate power supply with Swiss Lemo Fischer termination at both side by connecting with an original factory made cable with Fischer connectors. 5 individual transformers are used inside the power supply for supporting different function/operation of the DR-7 Pre-Amp.

- Its weight is about 25 Kg.

- A copy of user manual is included.

The DR-3 VHC Power Amp

- It is a PURE Class A High Current Design Power Amp without RELAY built inside.

- 45W output per Channel.

- It has two transformer inside for due channels operation.

- The DR-3 VHC in now running in STEREO mode and it can be set as a MONO BLOCK for operation. If setting as mono block, you need two for stereo setup.

- Its weight is about 45 Kg.

Please contact me via PM for whom is serious and interested to them. Thank you.

*** Some extra spare parts in NEW, such as Philips 4700u 40V capacitors and power switch of DR-7 power supply, will be given for free as gift for back up and long term maintenance to someone take the whole set as one go without bargain.

Following photos are for your reference only:

https://farm1.staticflickr.com/922/43099959001_271f093af7_b.jpg

https://farm2.staticflickr.com/1763/41299277780_3351526247_b.jpg

https://farm1.staticflickr.com/919/43439741681_8faae1a6b9_b.jpg

https://farm2.staticflickr.com/1770/29227476618_50a046411f_b.jpg

https://farm1.staticflickr.com/842/41288602240_88ab81b591_b.jpg

* Note: There are 6 original large capacitors, in RED color, under the green main board inside the power supply of the DR-7 preamp.

https://farm1.staticflickr.com/837/43099960251_6241a68eb2_b.jpg

https://farm2.staticflickr.com/1827/29227478508_ce9b37c15b_b.jpg


wlhuen
個人訊息 會員
138.xxx.xxx.142
2021-02-26 00:20
按照傳送日期顯示:由舊至新由舊至新  由新至舊由新至舊
最新資訊 - 影音
Sony 發布 PS5 四月份大更新,將推出新的儲存空間選項及社交功能 2021-04-13

最新資訊 - 影音
日本 TEAC 宣布立體聲後級放大器 AP-701 將延期推出 2021-04-12

最新資訊 - 影音
更耐用的專利 — SPEAR Labs nFORM XTR 耳棉 2021-04-12

最新資訊 - 影音
Zu Audio 推出全新 Soul 6 座地喇叭 2021-04-11


二手市場:只供會員買賣個人的物品,禁止一切商業活動及推廣。 所有物品買賣交易,一律均由買賣雙方直接洽商,而 review33.com 將不會負責核實買賣雙方所提供之資料。 所有爭議,一概與 review33.com 無關。 另外如有意在 review33.com 的二手市場內刊登收費廣告,請與我們聯絡 info@review33.com.