review33.com: 影音天地: Garrard 401 idler wheel問題

分類搜尋 移民 | 借錢 | 投資 | 物流 | 搬運 | 按揭 | 樓盤 | 保險 | 機票 | 酒店 | 升學 | 補習 | 手錶 | 電腦 | 紅酒 | 網購 | 脫髮 | 健身 | 減肥 | 濕疹

影音天地主旨 ﹝請按主旨作出回應﹞ 上頁下頁首頁尾頁

寄件者

傳送日期

[#41] Garrard 401 idler wheel問題我扭個Selector去熄机,個轆應該縮後左掂唔到platter. 如果個轆拖住的話,我諗捱唔到5秒....hahaaa		cobra 正式會員 182.xxx.xxx.220	2021-12-02 21:28

[#42] Garrard 401 idler wheel問題
haha ADD oiL

12 SEC IS QUITE BAD............. but it will be fine

this may help

https://pinkfishmedia.net/forum/threads/garrard-401-spindle-and-motor-service-instructions.187098/

hahayanyan

正式會員
49.xxx.xxx.19

2021-12-02 21:44

[#43] Garrard 401 idler wheel問題
haha any update ?

hahayanyan

正式會員
49.xxx.xxx.94

2021-12-08 13:36

[#44] Garrard 401 idler wheel問題
HaHa,昨天13：30我剛做緊手術HaHa

暫時要停幾日才搞,首先處理粒機米,支1.8mm螺絲批淘緊落來,
希望開到粒機米,另外想問no 2 grease問題,前排去中石化油站,
佢哋話冇得賣黃油,是否要去大間D中石化油站才有。

cobra

正式會員
183.xxx.xxx.197

2021-12-09 16:24

[#45] Garrard 401 idler wheel問題
通常係去嗰啲機油嘅分銷商可以買到

嫌麻煩唔想搵就喺淘寶訂返上嚟

做完手術都應該多多休息 haha play play table.. 都應該係一個幾好嘅休息活動

斷估你都明白摩打係邊個位置入油 haha

無聊想搵啲嘢玩, 係可以加一個電源供應器令轉速等等有更好嘅優化, from the lenco group people using a ac power supply.. Which alter the ac voltage and frewucy etc.
To get the right excat speed etc.., that powrr supply also ok for 401 type of motor.. I guess

Haha

最後修改時間: 2021-12-09 17:44:31

hahayanyan

正式會員
49.xxx.xxx.129

2021-12-09 17:41

[#46] Garrard 401 idler wheel問題
終於除埋佢件衫一窺全豹,甩埋粒機米啦。

最後修改時間: 2021-12-14 09:12:02

cobra

正式會員
182.xxx.xxx.176

2021-12-14 09:03

[#47] Garrard 401 idler wheel問題
Motor add oil 係未直接落B位3個孔位置,需要打開嗎？

A点枝軸承是否直接滴油落去就可以？

唔該大家（*_*）

最後修改時間: 2021-12-14 09:09:50

cobra

正式會員
182.xxx.xxx.176

2021-12-14 09:08

[#48] Garrard 401 idler wheel問題
雖然我沒有401, but oil to B see. Right

Haha

hahayanyan

正式會員
49.xxx.xxx.246

2021-12-14 10:40

[#49] Garrard 401 idler wheel問題
加晒油,都係32.6轉................太令人心碎了
玩玩吓盞燈仔都自己熄,一著機一閃即逝,乜事呀

跟住向第二個方向諗
電容問題(盞燈一閃即逝,會否跟電容有冇關係？
eddy current disc(係未指磁石個組嘢)

cobra

正式會員
182.xxx.xxx.176

2021-12-14 11:49

[#50] Garrard 401 idler wheel問題
#47

A is more direct
B are just rivets for holding the bushing cover.

8po

正式會員
61.xxx.xxx.194

2021-12-14 11:55

[#51] Garrard 401 idler wheel問題
#50
Motor 加油怎樣處理，ThX

cobra

正式會員
182.xxx.xxx.176

2021-12-14 12:06

[#52] Garrard 401 idler wheel問題
according to thios photo..it is really an oil inlet hole..around here

and there is always motor have such oil inlet hole too

hahayanyan

正式會員
49.xxx.xxx.246

2021-12-14 12:08

[#53] Garrard 401 idler wheel問題
重有樣嘢請敎,個motor都好鬼熱,有燙手感覺,正常嗎？

cobra

正式會員
182.xxx.xxx.176

2021-12-14 12:21

[#54] Garrard 401 idler wheel問題
i am not a garrard user, in general i would say..is ok for a motor less than 70 degree C (most magnet operate normal within 70 degree C)

if it reach 90 degree.......it may have issue, as some magnet lose power at such temperature

hot under loading or without loading ?

u have a infra red thermometer around ?

how clean is your idler ? need to be super clean...etc..

if u think u have done enough service...if u still having thsoe final kick of the speed... i would say...it is likely related to your idler condition ...

haha

最後修改時間: 2021-12-14 12:37:46

hahayanyan

正式會員
49.xxx.xxx.246

2021-12-14 12:28

[#55] Garrard 401 idler wheel問題
#51 add to A directly, just few drops
#52 the oil go thru the hole on eddy disc will end up to the sunken part of motor housing then the shaft. I will take our the eddy disc to oil it to save from mess.
#53 it runs quite warm, 5-60°up. If it is too hot, either the bushing is dried or too heavy load. Did you disassemble the motor before?

8po

正式會員
61.xxx.xxx.194

2021-12-14 15:01

[#56] Garrard 401 idler wheel問題
#55
未拆過,但係好有興趣想試,HaHa

cobra

正式會員
182.xxx.xxx.176

2021-12-14 16:13

[#57] Garrard 401 idler wheel問題
How's 45 speed setting

If it is only warm not hot..

Run it a few hours.. Haha

hahayanyan

正式會員
180.xxx.xxx.107

2021-12-14 16:18

[#58] Garrard 401 idler wheel問題
#56 can you measure the dia. of the motor pulley? @78rpm