兩聲道
CD機 | MD機 | SACD機 | DAC | CAS | 合拼擴音機 | 前級擴音機 | 後級擴音機 | 接線 | 喇叭線 | 揚聲器 | 耳機 | 耳機擴音機 | LP產品 | 膽機產品 | 開卷式錄音機 | 音響配件 | DIY音響 | 電源 | 家庭影院
電視機 | 投影機 | 錄影機 | DVD影碟機 | Blu-ray影碟機 | 多媒體播放器 | 機頂盒 | 多聲道擴音機 | 多聲道揚聲器 | 多聲道影音組合 | Mini音響組合 | 重低音揚聲器 | 輔助設備 | 同好會
同好會 | Accuphase | B&W | Burmester | Denon | Jadis | KEF | KRELL | Luxman | Marantz | Nuforce | OPPO | Pioneer | TEAC | WEISS | News
News | Blog | 其他
其他 | 所有 |
| 影音天地主旨 ﹝請按主旨作出回應﹞ 上頁 首頁 | 寄件者 | 傳送日期
|
| [#41] 聽黑膠高音失真，請高手救命!!! 試將兩唱頭Screw上緊, 一邊聽一邊加重唱頭重量。 |
goodsoundcable 正式會員116.xxx.xxx.45 |
2011-01-05 11:08 | |
|
|
|||
| [#42] 聽黑膠高音失真，請高手救命!!! How about swapping the headshell leads and see if the 拆聲 still coming out on the right channel? Or if you have a spare cart to change over? |
pakyeahpo 正式會員 202.xxx.xxx.143 |
2011-01-05 11:37 |
| [#43] 聽黑膠高音失真，請高手救命!!! swapping headshell leads had been tested. My two cartridges : BPS MKII and 17D3 have the same result. |
bigpanda 正式會員 116.xxx.xxx.135 |
2011-01-05 11:47 |
| [#44] 聽黑膠高音失真，請高手救命!!! 我phono amp係DIY EAR834p，經Lundhal LL1931 MC牛，試過用第二隻MC牛同唔用MC牛，無論碟頭尾都拆，幾隻碟都拆，因為新舊頭都拆，所以應該不是重量問題。Amp 同喇叭聽CD冇事。 ＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞ 1. Tracking force (VTF) 唔係主要問題, 因為如唱頭 set唔夠重係好易跳線，呢個現象好易睇到。加吾加spacer or extra weight 並不相關。另,加spacer係一個拆充方法將light weight 頭加在high mass 臂上,呢招要識嘅，加幾多至啱就係道行。 2. SME 對新手有好有唔好, 因佢過座可slide 前slide 後,如有郁過,要找Protrator幫手先可放precisely 地放回由spindle 到 215.35mm個位。信SME張跟臂紙皮呎..........把鬼!! 但就算支臂如有走位,只應片頭片後才有明顯失真? 片中間應較易出現正常聲......所以呢個case又未必係主因。.......Protrator就standy 住先。 3. VTA, 臂高度應該又唔係問題 (但SME set VTA 會影響音質頗大,其它用家可試, 以水平高小小最好聲)。因肉眼可見的水平範圍,唱頭聲音不會有太大差別。微調才是真功夫！ 4. Azimuth 又不是主因, 如上述所言肉眼睇到的, 音差不遠矣! 5. Anti Skate, 但凡set セ嘢以先, AS 應set 去level or 0, 而AS與sound 失真否是沒有大影響, 因AS design 的由來是平衡左右聲道的。樓主又試過了。 6.餘下.......應同 friend 借個 phono (with MC input is better)來試試, 唱頭 resistance loading 唔啱一定會由頭拆到尾, 用開廠貨的 C-hing未必一定aware,因大份廠phono set 在 47k ohms for MM and 100ohms for MC(呢過唔係絕對standard), 高級品種才多啲user settings。另 your EAR 845 係DIY, 又唔知有無高手郁過下加下D 補品咁, MC牛係 1:5 or 1:10放大(不同放大率會改变RC 值)相信問你都末必識答??呢個環節你比D料只有個Brand (重DIY)。 唯有化繁為簡 start from Zero !! MC loading link: http://www.hagtech.com/loading.html 當樓主做晒咁多嘢,而找回正常靚聲，你巳Pass Phono setting 101 了！ PS VPI + SME V + Dyna Karat 17 是好配搭, 蠻靚聲的。加個SDS就 very 骨啦！不然就考慮隔離牛, VPI motor 對AC current is very sensitive( 又300rpm motor 好過 600 rpm motor, check 下你個係セ?). 電唔靚會有尾音發氈狀態。 最後修改時間: 2011-01-05 12:01:48 |
and.t 正式會員 202.xxx.xxx.137 |
2011-01-05 11:54 |
| [#45] 聽黑膠高音失真，請高手救命!!! and.t 兄, 我用過 SME IV 同用緊 SME V, 跟臂 tools 好易 Set up, 唔係紙皮啦。就算 VTA 都好易調。 |
ozrayyau 正式會員 122.xxx.xxx.194 |
2011-01-05 17:35 |
| [#46] 聽黑膠高音失真，請高手救命!!! 跟臂 tools 好易 Set up, ＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞＞係好易，但唔精準。開臂窿還可以, overhang(應視為tangent cut)就唔夠精細！你無可能用果半條尺得知 mounting distance 係 215.35mm (度到0.35係有D誇,但約215.5係基本)。 唔係紙皮啦。＞＞＞＞＞＞＞＞＞＞你講果條有半支臂型outline 嘅jig,唔係紙皮就係膠片咯?? 用過認真D嘅 Protractor 後你會發覺 SME 嘅 set up jig 好兒戲！VPI都用綱的!! 就算 VTA 都好易調＞＞＞＞＞＞＞＞同意、夠用矣。 Damping油可用可不用.....不同用家各有所好。 但SME仍是world class好臂,只望小處有所於善！香港價位巳算平了。 最後修改時間: 2011-01-05 18:21:24 |
and.t 正式會員 202.xxx.xxx.137 |
2011-01-05 18:20 |
| [#47] 聽黑膠高音失真，請高手救命!!! 咁請問而家街價大概幾多? Thanks. |
ozrayyau 正式會員 122.xxx.xxx.194 |
2011-01-05 20:22 |
| [#48] 聽黑膠高音失真，請高手救命!!! 成日加,追唔切....09年尾2個上落,依家要行吓街先知....但美洲訂價比Tri-planar 同B44 Phathom都高。 香港 Phathom賣幾銀? 你可以計一計(問價可去三通check 一check)!! 至於 二手價 SME V 要注意, 因由20多年前production至今都無分 version 幾, version幾,而外觀又差唔多(bearing一定有分別),所以不宜只看asking price 來分底唔底,因03-04年時都只係皮零多D。New hand還是入新貨較穩陣。 最後修改時間: 2011-01-06 00:35:59 |
and.t 正式會員 219.xxx.xxx.65 |
2011-01-06 00:13 |
| [#49] 聽黑膠高音失真，請高手救命!!! I am not any expert of high-hand but one of my TT set-ups (VPI Aries + SME V + AT 33 ANV) is pretty similar with that of C-hing's. In my experience, SME V is not that difficult to set though I did not make use of any special tools but just the simple alignment protractor and bare eyes. I have the following to share in the last time I changed the stylus. After the re-setting, everything seemed normal not until I played the last track of a particular LP - there came the distortion and the arm even skidded. In the first place, I though the problem came from the LP because it did not happen to other LPs I played. But when I played the same LP on my other Linn set-up, it was perfectly OK. I then closely re-examined (with bare eyes again) the setting and I found the arm to appear not in a level position with the rear a bit tilting up. I then re-set the leveling and the VTA and everything became fine. I am not sure whether my above experience could help but since the the arm wand of SME V is not in uniform shape, it is worthy to re-check the leveling of the arm.  |
michael-Li 正式會員 112.xxx.xxx.250 |
2011-01-08 12:21 |
| [#50] 聽黑膠高音失真，請高手救命!!! 樓主的情況可能比你的Aries+SME V更複雜，他用VPI懸浮盤（HW-19?), 四條彈簧冇得校, 只是右邊聲道間歇性有問題... 最後修改時間: 2011-01-08 17:42:00 |
黃思璁 正式會員 202.xxx.xxx.33 |
2011-01-08 17:41 |
| [#51] 聽黑膠高音失真，請高手救命!!! Interested topic Problem resolved? Any finding? |
fm104 正式會員 14.xxx.xxx.46 |
2013-04-12 19:29 |
| [#52] 聽黑膠高音失真，請高手救命!!! I hope it had been solved. (It has to be clarified by Bigpanda) As magnified by digiscope, the coil inside the cartridge...... looked like just visited by spiderman. 最後修改時間: 2013-04-12 19:50:22 |
黃思璁 正式會員 1.xxx.xxx.219 |
2013-04-12 19:45 |
| [#53] 聽黑膠高音失真，請高手救命!!! bearing issue? |
yatchboats 會員 219.xxx.xxx.135 |
2022-01-22 13:50 |
