兩聲道
CD機 | MD機 | SACD機 | DAC | CAS | 合拼擴音機 | 前級擴音機 | 後級擴音機 | 接線 | 喇叭線 | 揚聲器 | 耳機 | 耳機擴音機 | LP產品 | 膽機產品 | 開卷式錄音機 | 音響配件 | DIY音響 | 電源 | 家庭影院
電視機 | 投影機 | 錄影機 | DVD影碟機 | Blu-ray影碟機 | 多媒體播放器 | 機頂盒 | 多聲道擴音機 | 多聲道揚聲器 | 多聲道影音組合 | Mini音響組合 | 重低音揚聲器 | 輔助設備 | 同好會
同好會 | Accuphase | B&W | Burmester | Denon | Jadis | KEF | KRELL | Luxman | Marantz | Nuforce | OPPO | Pioneer | TEAC | WEISS | News
News | Blog | 其他
其他 | 所有 |
影音天地主旨 ﹝請按主旨作出回應﹞ | 寄件者 | 傳送日期 |
[#1] 想問下emt 948 如果聽個時高音開叉要調教的咩野 想問下emt 948 如果聽個時高音開叉要調教的咩野.請高手個面指點下 |
gn3189 正式會員 121.xxx.xxx.146 |
2010-05-13 20:19 | |
|
[#2] 想問下emt 948 如果聽個時高音開叉要調教的咩野 玩得EMT948但會唔識校? |
孟波 正式會員 218.xxx.xxx.240 |
2010-05-13 21:24 |
[#3] 想問下emt 948 如果聽個時高音開叉要調教的咩野 整體來說只係差小小就係高音有小小開叉,其他野都收貨,請問有無高手可指點下 |
gn3189 正式會員 121.xxx.xxx.146 |
2010-05-13 21:55 |
[#4] 想問下emt 948 如果聽個時高音開叉要調教的咩野 如果肯定唱針正常,看看是否VTA校得太高。或者phono loading是否錯校? |
孟波 正式會員 218.xxx.xxx.240 |
2010-05-13 21:58 |
[#5] 想問下emt 948 如果聽個時高音開叉要調教的咩野 本人是黑膠新手,只係係人地屋企聰過emt948,覺得好好聲所以買入,我都幾肯定唱頭無問題,曷關剛剛係德國整過,請問咩叫vta呢,phono loading有係咩呢,請孟波兄指教一下小弟,必無言感激 |
gn3189 正式會員 121.xxx.xxx.146 |
2010-05-13 22:28 |
[#6] 想問下emt 948 如果聽個時高音開叉要調教的咩野 Sorry我未玩過EMT948.你連VTA都唔知好難講你聽。 建議你去請教人地屋企玩得好好聲既朋友應該重見效。 |
孟波 正式會員 218.xxx.xxx.240 |
2010-05-13 22:31 |
[#7] 想問下emt 948 如果聽個時高音開叉要調教的咩野 從側面影張"唱針落碟"相. 放大來睇下. |
k.c 正式會員 210.xxx.xxx.168 |
2010-05-13 22:32 |
[#8] 想問下emt 948 如果聽個時高音開叉要調教的咩野 咁就慘law.而家動態,底頻,音場都收貨 |
gn3189 正式會員 121.xxx.xxx.146 |
2010-05-13 22:33 |
[#9] 想問下emt 948 如果聽個時高音開叉要調教的咩野 孟波 hing is correct! Lower or Upper your arm to adjust your VTA. In this situation should be Lower your arm Phono loading should not be wrong in EMT 948 because it is internal Phono stage. |
n19137 正式會員 218.xxx.xxx.59 |
2010-05-13 22:58 |
[#10] 想問下emt 948 如果聽個時高音開叉要調教的咩野 n19137兄: 不知樓主自己有沒有更換其他唱頭,所以小弟提議他check loading,internal phono card唔知有冇loading impedance校呢? 剛check過EMT 948 manual,plug-in board有3級0/318/3180us equalization選擇,看看是否這裡校錯? 最後修改時間: 2010-05-13 23:21:43 |
孟波 正式會員 218.xxx.xxx.240 |
2010-05-13 23:07 |
[#11] 想問下emt 948 如果聽個時高音開叉要調教的咩野 舊年尾係新X聽過,剛好有樓主嘅情形有啲拆声,樓主唔知係咪嗰部嘅新機主? 個人觀点EMT名大於實.情意結吧!買來show-off則無妨.聽就.... |
格蘭斯班 正式會員 174.xxx.xxx.85 |
2010-05-14 01:45 |
[#12] 想問下emt 948 如果聽個時高音開叉要調教的咩野 好多948本身係用喺電台,24/7不停用咗幾十年.磨蝕一定有.有虛位tracking自然唔滑. 最後修改時間: 2010-05-14 02:59:57 |
格蘭斯班 正式會員 174.xxx.xxx.85 |
2010-05-14 02:48 |
[#13] 想問下emt 948 如果聽個時高音開叉要調教的咩野 there is not much to adjust in an emt948 if it works under a proper condition. if there is any defective electronic parts, that would be another matter. if the high frequency is not satisfactory, try to replace another pickup to verify the condition of your own pickup. as the damper in the pickup only last for 10 years even it is under seal. repairng a pickup like tsd-15 sfl cost about 500 euro. there is a gauge from emt to set the VTA which is a very easy job. if you do not have the gauge, set the bearing adjustment screw of the arm at 35 mm above the chassis (check vinyl engine for a copy of 948 manual). there may be chance that the loading to the eq. board 7 950 039 is overloaded. you may try to adj. the left and right levels on the board. the tonearm emt929 is fixed by 2 allen screws on the chassis, there is no chance of a gap if one tights up the screws in a secure manner. |
davwong 正式會員 203.xxx.xxx.117 |
2010-05-14 12:29 |
[#14] 想問下emt 948 如果聽個時高音開叉要調教的咩野 My humble suggestions of free self-inspection before go for costly professional service: a)Did you do the most basic set up step : leveling of the TT? This is one of the major cause of pitching in high tone for 948. Don't touch any part before you complete this step. b)are all the securing screws unwinding to the end? c)is the platter free flowing? d)if problem persist; take out all cards and check for trace of oxidation and reload them gently and securely. e)the metal panels of the 3 sides do need to put back for shielding purpose. f)making sure the XLR cable are in German config. g)after ll these done, then consider electronics fault Davewong and 孟波 c-hing approach. IMHO, 948 is one of the greatest TT ever made for practical use and good sound. Well constructed in rejection of external disturbance and easy to use. They sound fabulous even only with a low cost Grado MM head. Well deserves their reputation. |
com-buddy 正式會員 119.xxx.xxx.105 |
2010-05-14 13:44 |
[#15] 想問下emt 948 如果聽個時高音開叉要調教的咩野 剛剛整好啦,原來自己娥xlr l同r 反轉來插,反佐相,唔怪得的聲音怪怪地,而家正常反晒,emt 聲音可以盡情發揮,謝謝大家幫忙 |
gn3189 正式會員 121.xxx.xxx.234 |
2010-05-14 13:50 |
[#16] 想問下emt 948 如果聽個時高音開叉要調教的咩野 其實玩EMT盤真係買多好些發燒友用唔著既功能,個人會選擇盤,臂,頭,head amp/MC牛及RIAA放大電路自由配搭操控既系統。 當然每個發燒友都會有自己一套見解,自己滿意就OK. |
孟波 正式會員 218.xxx.xxx.240 |
2010-05-14 21:35 |
[#17] 想問下emt 948 如果聽個時高音開叉要調教的咩野 由EMT所產生的平衡度,全面性,專業質素,在使用十多年LP12之一段時期,未能體現;當使有過後配服不得了;當然,都是机會巧合才弄到手,到底EMT在市場上都属少數供應上品。擁有的物主真要多謝上天給我們机會與EMT机種的巧遇! 初玩LP的同好,若可遇上她,真的一步到站!盡享LP之樂,無需左調右配之苦。何樂之有!當然,有經驗的師兄、師父別論。 |
GW 正式會員 59.xxx.xxx.72 |
2010-08-02 23:14 |
[#18] 想問下emt 948 如果聽個時高音開叉要調教的咩野 GW hing, if you a/b 950 and 948, you will forget 948. it seems that your 948 is the 3rd generation. 948 in its 1st generation sounds the best, but still far away from 950. |
davwong 正式會員 123.xxx.xxx.100 |
2010-08-02 23:26 |
[#19] 想問下emt 948 如果聽個時高音開叉要調教的咩野 #17 LP12咁差? |
aheung 會員 219.xxx.xxx.5 |
2020-06-27 12:04 |
按照傳送日期顯示:由舊至新 由新至舊 |