兩聲道
CD機 | MD機 | SACD機 | DAC | CAS | 合拼擴音機 | 前級擴音機 | 後級擴音機 | 接線 | 喇叭線 | 揚聲器 | 耳機 | 耳機擴音機 | LP產品 | 膽機產品 | 開卷式錄音機 | 音響配件 | DIY音響 | 電源 | 家庭影院
電視機 | 投影機 | 錄影機 | DVD影碟機 | Blu-ray影碟機 | 多媒體播放器 | 機頂盒 | 多聲道擴音機 | 多聲道揚聲器 | 多聲道影音組合 | Mini音響組合 | 重低音揚聲器 | 輔助設備 | 同好會
同好會 | Accuphase | B&W | Burmester | Denon | Jadis | KEF | KRELL | Luxman | Marantz | Nuforce | OPPO | Pioneer | TEAC | WEISS | News
News | Blog | 其他
其他 | 所有 |
影音天地主旨 ﹝請按主旨作出回應﹞ 下頁 尾頁 | 寄件者 | 傳送日期 |
[#82] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? Wire enamel removal with aspirin utube: https://tinyurl.com/y4yqhatq |
cornercube 正式會員 119.xxx.xxx.12 |
2019-05-01 12:50 | |
|
[#81] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? Learn alot |
aheung 會員 219.xxx.xxx.133 |
2019-05-01 12:42 |
[#80] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? Hello 各位師兄, 我叫朋友幫我做了一條Cello+fisher線,不過發覺就算將音量擰到最小,喇叭都有小小聲,想請教一下是什麼出了問題,還有,將CD停了後,喇叭有嘶嘶聲,請幫幫忙。謝謝! |
allan6619 正式會員 203.xxx.xxx.233 |
2011-02-23 19:14 |
[#79] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? Thanks nagramen I think the method statement of 'Soldering Litz Conductors' from cardas is more professional than our trial and error. |
tigerdeer 正式會員 116.xxx.xxx.192 |
2011-02-08 23:48 |
[#78] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? Again... http://www.oyaide.com/diy/pg400.html |
PLL 正式會員 116.xxx.xxx.67 |
2011-02-07 22:44 |
[#77] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? http://www.cardas.com/content.php?area=faqs&content_id=5&pagestring=Cable+Construction Soldering Litz Conductors Q.) I'll be using a lot of your 21.5 gauge hookup wire for a project and I'm wondering about the best way to remove the litz coating before soldering. I am told that you use an acid, which would probably work best for me. If so, can you tell me what that acid is, and at what strength you use it? A.) Do not use acid of any type! Do not try to burn off the insulation with a flame! There are several things that you can do: We have a termination kit that will work for a project or if you are going into production we can put a faster method together. If you want to try it yourself here are some of the ways you can do it. 1. Use a solder pot (best, easiest and most reliable) 2. Sand off (220-320-grit wet or dry unravel strand and lay flat on table, a couple of strokes on each side) the insulation and use a little rosin flux on the wire. With a good 900 degree Fahrenheit (482 degrees Celsius) tip on a 100 watt iron you can pre-tin the wire. 3. Twist a little piece of unenamled wire around the litz such as a resistor lead and solder normally using using some rosin flux (such as Kester sp88). Heat the bare copper wire you have wound around the litz and add solder and rosin flux until you see the litz suck up the solder. 4. If the wire is to be soldered to a pc board, placed through an eyelet, crimped in a spade or other connector or otherwise surrounded by solder. In a closed loop you can solder it by just putting a little rosin flux on the wire as you twist the strands after stripping. On the surrounding piece of metal heat the metal or the very tip of the Cardas litz and watch for the smoke of the coating coming off and the tinning of the wire near the surrounding metal. 5. You can pre tin the wire by applying some rosin flux during the striping operation and heating the very tip of the wire in a pool of solder on the tip (850-900 degrees F) of a 100w Iron. 6. You can get a large iron with a hot tip and dimple the tip so that it will hold a little solder and use it for a solder pot. |
nagramen 正式會員 58.xxx.xxx.131 |
2011-02-07 21:40 |
[#76] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? Others good example. (note that the connection of shielding GND) http://colomar.com/Shavano/xlr_cable.html 最後修改時間: 2011-02-07 20:13:13 |
PLL 正式會員 116.xxx.xxx.67 |
2011-02-07 20:01 |
[#75] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? Reminder: http://en.wikipedia.org/wiki/XLR_connector @@' |
PLL 正式會員 116.xxx.xxx.67 |
2011-02-07 19:17 |
[#74] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? 一如我事前話, D 漆殘餘物會留在上了錫的銅線同膠皮之間, 清楚可見, 一切預料之中, 順利成功!!值得一提, D 膠皮雖不是 Teflon, 但肯定都耐高温, 貴野質地。 bye-bye |
254mm 正式會員 203.xxx.xxx.122 |
2011-02-07 19:02 |
[#73] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? 睇老兄的器材及線材, Sanwa 電子他錶, Hakko 衡温 Soldering Gun, Goat 熔錫爐, Hi-Fi(Audio Note), 絕不等閑, 當 experiment 做算啦, 証明自己做到啦, 亦做過成功, 老兄兩個時鐘點只揾 $100, 下次找人代勞吧。 |
254mm 正式會員 203.xxx.xxx.122 |
2011-02-07 18:53 |
[#72] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? 我在 R33 教別人的 solution, 實行得通, 因為我身先士卒, 一定做過成功才敢教別人, 絕不 building castles in the air!! 所以點會 pointless 呢, 証明說此話的人是幾無知。 |
254mm 正式會員 203.xxx.xxx.122 |
2011-02-07 18:42 |
[#71] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? 老兄你就大把器材, 欲善其事, 先利其器, 多謝選用我教的方法, 第一次做浸錫都效果不錯, 最緊要得其法。 |
254mm 正式會員 203.xxx.xxx.122 |
2011-02-07 18:37 |
[#70] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? Cello string I,以前在萬宜大廈買時,他們都有教慢慢用辣雞除漆皮的。全部用 String I,聲底會是較淡。 |
gingergarlac 正式會員 183.xxx.xxx.66 |
2011-02-07 16:43 |
[#69] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? 谢谢师兄指教!我还以为一样的呢! |
MetalNuts 正式會員 58.xxx.xxx.236 |
2011-02-07 16:13 |
[#68] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? NetalNuts 兄, 普通電綫的叫膠皮而非漆皮。漆皮是銅綫噴焗上去的絕缘油, 是非常薄的一層, 平常我們見的火牛裏的漆包線就是這種, 因為非常薄之故, 用脱綫鉗是拉不出的, 只能刮或省去, 或用温度去融化這些絕緣油, 令其離開銅綫表面。 |
yukclee 正式會員 218.xxx.xxx.38 |
2011-02-07 15:55 |
[#67] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? 個人較喜Oyaide的XLR插多過Furutech的 ==================== Hi Mr. Lee, My next plan is to made 2 x 4M pairs for XVR-1 to Performance amps. I will consider your suggestion. Thanks again! 要去看醫生啦 ... Bye now! ^___^ 最後修改時間: 2011-02-07 15:50:35 |
sktung 正式會員 124.xxx.xxx.46 |
2011-02-07 15:50 |
[#66] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? 恭喜恭喜! 事非經過不知難。要做過才知道要求該如何。 不做就永遠不知。但做一次並非以後次次都做, 這是我個人人生態度.否則永遠只是付錢機器..:-D P.S. 個人較喜Oyaide的XLR插多過Furutech的 |
yukclee 正式會員 218.xxx.xxx.38 |
2011-02-07 15:45 |
[#65] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? Done! ^___^ |
sktung 正式會員 124.xxx.xxx.46 |
2011-02-07 15:35 |
[#64] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? 把漆皮線 twist tight and dip into a solder pot 416^c for 5 seconds 的結果如下圖. |
sktung 正式會員 124.xxx.xxx.46 |
2011-02-07 15:35 |
[#63] 請問有乜辨法可以很容易除去 conductor 表面的 coating (柒皮) 呢? 请问师兄,这和平日我们把电线的漆皮除去放到插苏里上螺丝有什么分别呢?是否这些线的漆皮是溶合到金属线里不能扯开。不然的话,有些钳有不同大小的圆孔,只要把线放在大小合适的孔转一圈,那一截的漆皮就会跟其它的分开,在用点力就能把该截漆皮拉出,那时你喜欢用螺丝上死也好,用焊焊死也可以咯! 若我误会了坛主的问题,请见谅! |
MetalNuts 正式會員 58.xxx.xxx.236 |
2011-02-07 15:34 |