兩聲道
CD機 | MD機 | SACD機 | DAC | CAS | 合拼擴音機 | 前級擴音機 | 後級擴音機 | 接線 | 喇叭線 | 揚聲器 | 耳機 | 耳機擴音機 | LP產品 | 膽機產品 | 開卷式錄音機 | 音響配件 | DIY音響 | 電源 | 家庭影院
電視機 | 投影機 | 錄影機 | DVD影碟機 | Blu-ray影碟機 | 多媒體播放器 | 機頂盒 | 多聲道擴音機 | 多聲道揚聲器 | 多聲道影音組合 | Mini音響組合 | 重低音揚聲器 | 輔助設備 | 同好會
同好會 | Accuphase | B&W | Burmester | Denon | Jadis | KEF | KRELL | Luxman | Marantz | Nuforce | OPPO | Pioneer | TEAC | WEISS | News
News | Blog | 其他
其他 | 所有 |
影音天地主旨 ﹝請按主旨作出回應﹞ 下頁 尾頁 | 寄件者 | 傳送日期 |
[#1] Quad 405-2 接 tube pre amp 問題 部Quad 405-2 一接膽前級會出現沙沙聲﹐部前級本身冇事。 想問405-2幾樣野 1. 係咪high input sensitive﹐唔適合駁膽前級 2. 係咪gain 太大 3. 本身個output voltage limiter應唔應該bypass, 點做? thanks |
pksam 正式會員 203.xxx.xxx.169 |
2009-04-27 22:09 | |
|
[#2] Quad 405-2 接 tube pre amp 問題 405。2接膽機要留意接地問題,其實最夾都是配回同廠前級,34&44,一流的英國聲,可惜我早前放走左,後悔。 |
open 正式會員 64.xxx.xxx.54 |
2009-04-27 22:35 |
[#3] Quad 405-2 接 tube pre amp 問題 My experience is Quad 405-2 input sensitivity is quite high. When it match with tube preamp, it will have higher noise level. So it is best match with Quad 34, 44, which have small gain. It should be ok to match with quad QC24 tube preamp. |
LFYeung 正式會員 219.xxx.xxx.36 |
2009-04-27 22:40 |
[#4] Quad 405-2 接 tube pre amp 問題 You may lower the gain from the 405.2 I have connected the 405.2 with 34 and tube pre-amp but need to adjust the vr at the back of the 405.2 |
davelm 正式會員 203.xxx.xxx.183 |
2009-04-27 23:08 |
[#5] Quad 405-2 接 tube pre amp 問題 搵唔到後面有vr 係咪調個bias? 應該唔係gain 唔敢亂調 |
pksam 正式會員 203.xxx.xxx.169 |
2009-04-29 21:02 |
[#6] Quad 405-2 接 tube pre amp 問題 後面得一個可以扭,由0-2V,就係個粒。 |
unicity 正式會員 221.xxx.xxx.133 |
2009-04-29 23:00 |
[#7] Quad 405-2 接 tube pre amp 問題 冇得扭 |
pksam 正式會員 203.xxx.xxx.169 |
2009-04-29 23:56 |
[#8] Quad 405-2 接 tube pre amp 問題 Hi Pksam: 閣下部機背後是否同圖片一樣?早期版是前面405.2是白色 後期版是灰色有翰入調望訊號大小VR. |
happyquad 正式會員 220.xxx.xxx.247 |
2009-04-30 00:09 |
[#9] Quad 405-2 接 tube pre amp 問題 happyquad: 點解我的白面和灰面的405.2都有VR? |
unicity 正式會員 221.xxx.xxx.133 |
2009-04-30 01:26 |
[#10] Quad 405-2 接 tube pre amp 問題 請貼張圖片看看!閣下部白面機背後輸入是什麼插座. 早期是4Pin插座 |
happyquad 正式會員 220.xxx.xxx.247 |
2009-04-30 01:40 |
[#11] Quad 405-2 接 tube pre amp 問題 早期翰入是用4Pin插座. Photo 1: |
happyquad 正式會員 220.xxx.xxx.247 |
2009-04-30 02:06 |
[#12] Quad 405-2 接 tube pre amp 問題 Photo 2: |
happyquad 正式會員 220.xxx.xxx.247 |
2009-04-30 02:07 |
[#13] Quad 405-2 接 tube pre amp 問題 **點解我的白面和灰面的405.2都有VR?** 白面405.2是有不同期產品. |
happyquad 正式會員 220.xxx.xxx.247 |
2009-04-30 02:10 |
[#14] Quad 405-2 接 tube pre amp 問題 This is a common problem -: 1. Quad 405 as far as I remember is DIN specification ( 0.5 V ), hence the input sensitivty is higher than USA or Japan power amp. 2. Some tube preamp has output impedance it bit too high for transistor power amp. 3. Tube amp has tube hiss. One has to either reduce the sensitivity by adding a volume control or better a voltage divider. What circuit/made is your preamp? |
ModernClassic 正式會員 112.xxx.xxx.205 |
2009-04-30 05:13 |
[#15] Quad 405-2 接 tube pre amp 問題 咁樣 |
pksam 正式會員 59.xxx.xxx.225 |
2009-04-30 13:54 |
[#16] Quad 405-2 接 tube pre amp 問題 如用一般喇叭, 應唔應該bypass output voltage limiter? 效果係點, 有冇人試過? 仲有QC24 + 405.2 呢個組合 會唔會出事呢? |
pksam 正式會員 59.xxx.xxx.225 |
2009-04-30 13:58 |
[#17] Quad 405-2 接 tube pre amp 問題 你部機係唔係二手買返來?好似摩過。 |
unicity 正式會員 221.xxx.xxx.133 |
2009-04-30 22:01 |
[#18] Quad 405-2 接 tube pre amp 問題 好想玩膽前+405-2做後級,但通常低噪好大, 想用來推sl6si 或者有沒有ching用過其他膽前夾405,沒有低噪問題的 先謝過了! 最後修改時間: 2014-04-16 11:20:10 |
leicam6classic 正式會員 119.xxx.xxx.244 |
2014-04-16 11:17 |
[#19] Quad 405-2 接 tube pre amp 問題 Ching, Is the noise exist only with tube pre-amp or it comes from the amp board itself? Some aged component will result in high hum noise such as C5 You may change some resistors and caps value to adjust the input sensitivity. FYI! http://www.dadaelectronics.eu/ForumRetrieve.aspx?ForumID=317&TopicID=10260&NoTemplate=False |
shungyan 正式會員 14.xxx.xxx.165 |
2014-04-16 13:15 |
[#20] Quad 405-2 接 tube pre amp 問題 在405輸入串多個volume就無問題, 不過要DiY |
zoneaudio 正式會員 14.xxx.xxx.185 |
2014-04-16 13:40 |