談天說地主旨 ﹝請按主旨作出回應﹞ | 寄件者 | 傳送日期 |
[#1] 換分體式冷氣機一問 用咗近廿年的樂聲牌分體式冷氣機終于壽終正寢,現在想換新機。 請問有冇師兄知道換那個牌子的分體新機可以換機唔換喉? |
corbe 正式會員 118.xxx.xxx.218 |
2019-07-26 21:13 | |
|
[#2] 換分體式冷氣機一問 無 ...雪種不同,制式,壓力 |
city_man 正式會員 42.xxx.xxx.160 |
2019-07-26 21:16 |
[#3] 換分體式冷氣機一問 新机全部用新雪種 壓力更大 舊喉薄 唔啱用! 最後修改時間: 2019-07-26 21:17:32 |
伊雲士 正式會員 223.xxx.xxx.241 |
2019-07-26 21:16 |
[#4] 換分體式冷氣機一問 There are still R22 split units available from Taobao.(already shipped 2 nos and installed) But you would not love such Chinese brand. 最後修改時間: 2019-07-26 21:24:28 |
alexanderkoo 正式會員 219.xxx.xxx.23 |
2019-07-26 21:24 |
[#5] 換分體式冷氣機一問 多謝各位師兄意見。 會就住自己荷包及考慮環保因素換新機。 謝謝 |
corbe 正式會員 118.xxx.xxx.218 |
2019-07-26 21:39 |
[#6] 換分體式冷氣機一問 就算有,你現有d喉都用咗20年啦⋯ |
ez3119 正式會員 182.xxx.xxx.146 |
2019-07-27 07:22 |
[#7] 換分體式冷氣機一問 師兄,你都系要花D$比人裝啦,條銅喉接駁時已焊死系部出風機度啦,重有新機返尼開機前需抽真空,你都冇那個泵。 |
jobim888 正式會員 141.xxx.xxx.145 |
2019-07-27 08:03 |
[#8] 換分體式冷氣機一問 聯發仲有R22賣 |
謝x庭 正式會員 203.xxx.xxx.193 |
2019-07-27 08:37 |
[#9] 換分體式冷氣機一問 #7 not brazed but flare jointed. Still need to cut a bit and flare. Concealed? Hence, difficult to replace. |
alexanderkoo 正式會員 203.xxx.xxx.35 |
2019-07-27 10:47 |
[#10] 換分體式冷氣機一問 我同ching你一樣部2匹半樂聲分體用左20年,一直好凍,但近兩年主機控制版出問題,遙控器換左幾個都係唔一定開到機,要用墻身電制做開關,上個月終於決定換機,大金2匹變頻淨冷新雪種,搭棚連換曬新銅喉,差不多2皮,無原來甘凍但真係超靜,早知換返2匹半,但都好滿意。 |
有料到 正式會員 121.xxx.xxx.162 |
2019-07-27 10:49 |
[#11] 換分體式冷氣機一問 #9, 我部就用銅銲、師傅好認真 佢話R410 高壓丶易慢漏丶越少flare 接位越好丶做 flare 要用靚料零件及正確扭力丶佢話淘寶貨flare joint 易出事、吾想在保養期內再來丶如入左牆丶更難再處理 唯一flare joint 是在室外機接口 最後修改時間: 2019-07-27 15:39:02 |
phil.ng 會員 223.xxx.xxx.7 |
2019-07-27 15:28 |
[#12] 換分體式冷氣機一問 Never heard of such brazing at the 4 flared joints, difficult to take down for repair. Basically use torque wrench for tightening the nuts.(18 and 40Nm for 1 hp unit, low and high pressure tubes, got the Yellow Jacket wrenches) Use bond steel to strengthen the joint mechanically, should be OK, though still the weakest part of the system. Nylog sealant applied at the joint, can go through vacuum test easily. Already overkill. Brazing is for jointing 2 tubes(with nitrogen passing inside to avoid oxidation), should not use flared nuts due to weak strength.MV Now what, R32, can be even worse due to higher working pressure. Installed 2 nos. R22 split units(re-using indoor units and copper tube) and one "3/4 hp window unit(405mm width, 1600 cooling watt only) inside kitchen" and one 4kW pressure type electric water heater, last 2 month. CMV R22 1hp unit, RMB 1200, buy only if you can DIY. If installation entrusted to C-fu(high installation cost, sometimes, need scaffolding), better have Panny or Daikin. 最後修改時間: 2019-07-28 09:52:11 |
alexanderkoo 正式會員 219.xxx.xxx.184 |
2019-07-28 09:36 |
[#13] 換分體式冷氣機一問 https://item.taobao.com/item.htm?spm=a1z0d.6639537.1997196601.37.24f55886xhYxHn&id=576778813198 Taopai shipment, around HK 5/kg, add $25 for general local delivery but $110 for remote area.(Mid-levels etc) 最後修改時間: 2019-07-28 09:57:44 |
alexanderkoo 正式會員 219.xxx.xxx.184 |
2019-07-28 09:53 |
[#14] 換分體式冷氣機一問 8:45 mentions there is another problem with welding if it is not done properly. |
bach 正式會員 61.xxx.xxx.68 |
2019-07-28 10:00 |
按照傳送日期顯示:由舊至新 由新至舊 |