談天說地主旨 ﹝請按主旨作出回應﹞ 下頁 尾頁 | 寄件者 | 傳送日期 |
[#1] 抽濕機修理問題 最近部抽濕機按開關無反應開唔倒機。世上又多左舊電子垃圾…用三四年倒仲幾新下:< 這幾天放假得閒臨掉前爆開部機盡下人士,原來是個開關制內部爛左touch唔倒個micro switch.咁這個我懂得整。部機就著得番。不過發現另一問題就是個濕度顯示有問題長期低過30%。是否濕度sensor有問題?通常放在那位置?謝各位幫忙。 Panasonic F-YCH23H |
hhseasea 正式會員 42.xxx.xxx.188 |
2018-02-21 16:23 | |
|
[#2] 抽濕機修理問題 我未拆過抽濕機, 但有人拆過, 不過牌子唔同. http://blog.xuite.net/mr.coffee/diary/212526868-%E3%80%90%E9%96%8B%E7%AE%B1%E3%80%91%E9%99%A4%E6%BF%95%E6%A9%9F%E8%84%AB%E5%85%89%E5%85%89%E6%94%B9%E8%A3%9D%EF%BC%8C%E6%B7%BA%E8%AB%87%E7%86%B1%E4%BA%A4%E6%8F%9B%E5%8E%9F%E7%90%86 |
呀金 正式會員 113.xxx.xxx.157 |
2018-02-21 16:52 |
[#3] 抽濕機修理問題 現濕度九十二,開窗丶放近丶應見很高濕度 |
phil.ng 會員 223.xxx.xxx.7 |
2018-02-21 17:08 |
[#4] 抽濕機修理問題 The sensor is of capacitance principle, faulty sensor would not affect running in high/low modes.(only for auto mode or indication) Can clean a bit using isopropyl alcohol.(next to the water tank) I serviced my dehumidifiers by taking them apart, much dirt was trapped between the cooling/heating coils due to their proximity. Oasis is easy to service(spacious inside, large cooling coil) but the Japan ones would simply crack after servicing a few times.(compact and having many screws) I picked up two dehumidifers from trash, one Sharp(still using), the other Mitsubishi(dumped after a few years due to low capacity) Only minor repair/cleaning.(tank switch/triac problems) Both MIJ. |
alexanderkoo 正式會員 42.xxx.xxx.114 |
2018-02-21 17:08 |
[#5] 抽濕機修理問題 是否濕度sensor有問題? There are 2 major types of humidity sensor used in consumer electronic product A. Impedance type (POLYMER), 白色長方形 ceramic plate with black/golden color polymer coating, coating pattern 似2隻手指 E 互相對住. Rectangualr shape housing or bear element Cheap, easy design and programming, LOW RELIABILITY, higher tolerance, few years of life time (even no operate), impedance riased up (low RH reading) Applications : Clock, 電器, Indoor purpose B. Capacitive type (semiconductor), very small element like size around 1.0mm^2, with round shape housing. Expensive, difficult hardwear / software design and trimming, higher accuracy, Very Relaiable Applications : Equipment, Outdoor measurement 其實抽濕,冷氣用 humidity sensor 係無必要, 除非你確定用 capacitive type sensor, 否則部機好大機會幾年後報癈. 20年前日本仔頂級 Impedance type humidity sensor 都玩到5~10年, 近 1x 年韓仔/Taiwan HS更短命, 你會發現 Humidity reading 越來越低, RH reading 直至到 software design lower limit e.g. 20% RH (even real RH 90%), sensor 放幾年 coating 就算冇電 measurement 都會死. 樓主 case 可以去配 humidity sensor or replace by a 1K ohm 5% resistor (as a dummy sensor, will display a fixed high RH % reading) 最後修改時間: 2018-02-22 12:58:46 |
nickmanwoo 正式會員 61.xxx.xxx.173 |
2018-02-22 12:55 |
[#6] 抽濕機修理問題 原本放棄了,見咁多兄弟支持。拆一拆。請問是否這個? 勁多塵… 最後修改時間: 2018-02-22 13:51:38 |
hhseasea 正式會員 1.xxx.xxx.61 |
2018-02-22 13:47 |
[#7] 抽濕機修理問題 This one |
hhseasea 正式會員 1.xxx.xxx.61 |
2018-02-22 13:51 |
[#8] 抽濕機修理問題 Yes, The HS is under the screw |
nickmanwoo 正式會員 61.xxx.xxx.173 |
2018-02-22 13:52 |
[#9] 抽濕機修理問題 我試試清潔下work 唔work. 若果用電錶請問怎樣check? |
hhseasea 正式會員 1.xxx.xxx.61 |
2018-02-22 14:01 |
[#10] 抽濕機修理問題 唔可以清潔 i.e. water, cleaner ....即死 其實粒 HS 已經 aged (dead) HS 用 1KHz sinewave 0.5Vp-p max 去測量 impedance Impedance 係 AC resistance, 即是它表(DC)度唔到, 除非用 LCZ (L.C.R impedance meter) 我估粒 HS part number is SYH-2 或者你用 resistor 做 dummy sensor 把 reading trim到 80% RH (compressor operating mode) 最後修改時間: 2018-02-22 14:07:12 |
nickmanwoo 正式會員 61.xxx.xxx.173 |
2018-02-22 14:06 |
[#11] 抽濕機修理問題 In your picture Green color disc shape is temperature sensor (NTC thermistor), used for measure the ambient temperature and compensation of humidity sensor temperature drift characteristics. |
nickmanwoo 正式會員 61.xxx.xxx.173 |
2018-02-22 14:14 |
[#12] 抽濕機修理問題 個sensor唔系焊上去的 而系用膠黏上底板,然後插入個三腳socket 可能為了方便更換 你搵到個snesor好易換 去TB試下 |
Kelvinzy 正式會員 202.xxx.xxx.40 |
2018-02-22 14:18 |
[#13] 抽濕機修理問題 塊pcb得一粒螺絲一個connector, 拆出來睇吓啦。 |
呀金 正式會員 113.xxx.xxx.157 |
2018-02-22 14:19 |
[#14] 抽濕機修理問題 請問有無得成塊板買?應該唔work了..... |
hhseasea 正式會員 1.xxx.xxx.61 |
2018-02-22 14:46 |
[#15] 抽濕機修理問題 你試下淘 可能濕度讀數差+/-15%左右,但起碼部机 work |
Nickmanwoo 正式會員 14.xxx.xxx.149 |
2018-02-22 15:00 |
[#16] 抽濕機修理問題 成塊板買比較難,淘寶都未必有,不過都可以打個part number試吓查。 |
呀金 正式會員 113.xxx.xxx.157 |
2018-02-22 15:17 |
[#17] 抽濕機修理問題 Humidity sensor 銲接完後要等15分後才能正常工作 因為銲鐵的高溫會把Polymer coating 中的水氣全部揮發 買多幾粒,必要時2粒並聯用去較正。reading HS (impedance Vs RH)特性大同小異, log scale decay |
Nickmanwoo 正式會員 14.xxx.xxx.149 |
2018-02-22 15:40 |
[#18] 抽濕機修理問題 請問華輝有冇買?淘寶無戶口。 |
hhseasea 正式會員 1.xxx.xxx.61 |
2018-02-22 15:40 |
[#19] 抽濕機修理問題 華輝 應該有, make a call before you go |
Nickmanwoo 正式會員 14.xxx.xxx.149 |
2018-02-22 15:47 |
[#20] 抽濕機修理問題 你可以把 humidity sensor short circuit, display 可能出 99% RH, 部机正常抽濕。 咁証明 Sensor 問題,才去配零件 |
Nickmanwoo 正式會員 14.xxx.xxx.149 |
2018-02-22 16:24 |