| 談天說地主旨 ﹝請按主旨作出回應﹞ | 寄件者 | 傳送日期
|
| [#1] 油煙機安裝問題 煮食爐放窗口位，冇牆掛油煙機，問過大間既如煤氣公司唔會接，有冇計？ |
沉默的膏蟹 正式會員58.xxx.xxx.198 |
2019-10-14 14:27 | |
|
|
|||
| [#2] 油煙機安裝問題 from google: 島式抽油煙機 https://tinyurl.com/yxtrj998 https://tinyurl.com/y2xjuxvj 最後修改時間: 2019-10-14 14:43:24 |
cornercube 正式會員 58.xxx.xxx.34 |
2019-10-14 14:37 |
| [#3] 油煙機安裝問題 安裝應該唔平。 |
呀金 正式會員 113.xxx.xxx.2 |
2019-10-14 14:46 |
| [#4] 油煙機安裝問題 如果另計 https://tinyurl.com/y24sz6xb |
cornercube 正式會員 58.xxx.xxx.34 |
2019-10-14 14:59 |
| [#5] 油煙機安裝問題 有冇安裝位置相？ |
Tommy913 正式會員 218.xxx.xxx.38 |
2019-10-14 15:01 |
| [#6] 油煙機安裝問題 幫個老人問，冇相，佢想裝傳統台式機。 |
沉默的膏蟹 正式會員 14.xxx.xxx.127 |
2019-10-14 16:04 |
| [#7] 油煙機安裝問題 在背後做個鋁架，兩邊食牆身力，再將油煙機裝在鋁架上。 |
dindunlo 正式會員 14.xxx.xxx.104 |
2019-10-14 16:06 |
| [#8] 油煙機安裝問題 封窗一定可以, 不過又摭左光  |
Ronny33 正式會員 59.xxx.xxx.186 |
2019-10-14 16:10 |
| [#9] 油煙機安裝問題 點都要搵個師父睇睇,實做到, 大公司只做標準安裝或報天價.  |
Ronny33 正式會員 59.xxx.xxx.186 |
2019-10-14 16:12 |
| [#10] 油煙機安裝問題 想裝傳統機, 但冇牆靠. or try 用方通 燒 兩條 U字 或 倒L字 由天花落.... |
cornercube 正式會員 58.xxx.xxx.34 |
2019-10-14 16:25 |
| [#11] 油煙機安裝問題 In fact, no need to install kitchen hood. An exhaust fan at lower level, next to the stove would be ok. Saw installation like this. Most hoods are not effective due to 400mm clearance between hood and stove, hence low capturing velocity. Sucking surrounding air instead of oil fume. Inclined type is slightly better. |
alexanderkoo 正式會員 58.xxx.xxx.37 |
2019-10-14 16:41 |
| [#13] 油煙機安裝問題 用長絲桿由天花吊下 |
awk 正式會員 203.xxx.xxx.29 |
2019-10-14 17:41 |
| [#14] 油煙機安裝問題 ＞＞#10... -------------------------- 諗諗下, 由天花落 幾危險..鬆... |
cornercube 正式會員 58.xxx.xxx.34 |
2019-10-14 17:42 |
| [#15] 油煙機安裝問題 #2 島式抽油煙機 ============== 島式要樓底較高兼要假天花。 |
Dlbf 正式會員 14.xxx.xxx.68 |
2019-10-14 17:53 |
| [#16] 油煙機安裝問題 N 咁多個方法，如果樓主唔提供相關位置圖片，好難提供最快捷,最便宜和最值得做的！ |
0925 正式會員 219.xxx.xxx.93 |
2019-10-14 20:01 |
| [#17] 油煙機安裝問題 抽油煙機唔係幾重架收兩口拉爆咪搞掂囉。使乜由天花吊落嚟呀。要平靚正買太平洋嗰隻 3033 型號千六七左右，2800 轉大大力抽，啱啱先幫朋友裝完。一係就搵樓下水電舖啲師傅，講下價400蚊淨裝合理價。 |
jobim888 正式會員 141.xxx.xxx.149 |
2019-10-15 08:04 |
| [#18] 油煙機安裝問題 Many C fu's would use long self-taping screw for installing kitchen hood, I would use anchorage bolt for safety reason.(same for TV installation) Got the Misoko inclined hood(auto de-greasing using built in heater, MIT Taiwan) and DIY installed. More difficult part is the opening to the surrounding, acrylic scrape sheet from Lockhart road, $30, jigsaw for the opening, must clamp/support tightly to avoid chipping) Done. The other Panny 25 yo hood with long exhaust duct of 13ft.(replacement was difficult since left hand exhaust was via kitchen cabinet) Add an in-line booster fan(150mm, RMB 200 from Taobao) and non-return flap RMB 30, much better ventilation. Use the existing hood lighting switch as control switch for the new fan.(hence can run both fans by pressing two buttons) 最後修改時間: 2019-10-15 09:26:33 |
alexanderkoo 正式會員 219.xxx.xxx.187 |
2019-10-15 09:19 |
| [#19] 油煙機安裝問題 諗諗下, 由天花落 幾危險..鬆... ...................... 先打四粒拉爆，成千磅都Ok丶吊櫃都是這樣做 |
phil.ng 會員 223.xxx.xxx.7 |
2019-10-15 09:21 |
| [#20] 油煙機安裝問題 ＞＞#19...四粒拉爆，成千磅... --------------------------- 吊扇 變 血滴子...我聽過 https://tinyurl.com/y2lczsaa |
cornercube 正式會員 112.xxx.xxx.242 |
2019-10-15 09:45 |
