談天說地主旨 ﹝請按主旨作出回應﹞ 上頁 首頁 | 寄件者 | 傳送日期 |
[#41] 換電制求救 >> #37,估計2條N唔夠長直接Jam落去個肉度所以要駁長佢。 |
AndyTKO 正式會員 14.xxx.xxx.206 |
2019-10-29 22:50 | |
|
[#42] 換電制求救 佢條 N 線係咪只接左粒燈? |
呀金 正式會員 113.xxx.xxx.2 |
2019-10-29 23:29 |
[#43] 換電制求救 Cable was too short< 落簪肉駁長條線后個簪肉包一包電工膠布或自溶膠布安全一o的(接駁位不會屈折和同其它金屬觸碰;如果自己屋我會用辣雞銲錫駁長同線號的再套熱縮管),如果兩條黑線都唔夠長就分開駁長再接個double pole cooker switch "Line N" 同 "Load N"。 好多人的確是煤氣爐配用普通燈掣< 而家煤氣公司會幫客裝個帶fuse的開關,可能防個爐出事水浸短路,不過條fuse 係13A,轉3或5A合理D。 最後修改時間: 2019-10-30 02:10:21 |
0925 正式會員 219.xxx.xxx.122 |
2019-10-30 01:59 |
[#44] 換電制求救 #42, nope, incoming and outgoing neutral cables wired on same terminal. For jointing especially for high current carrying(15A for this case, 3kW water heater, mine is 4kW for fast heating)Must have both mechanical strength and good conductivity.(crimping, at least twisting the wires, plus soldering as in Industry) A terminal is not too useful, may become loosened/overheated. In workshop, I was trained on married joint. The cable conductors were interwined with those of the other cable and then soldered. But never seen in Industry.(in fact, avoid jointing except underground cable, must have joints due to long length and tee offs) 最後修改時間: 2019-10-30 06:55:36 |
alexanderkoo 正式會員 58.xxx.xxx.3 |
2019-10-30 06:47 |
[#45] 換電制求救 最後修改時間: 2019-10-30 08:41:24 |
0925 正式會員 219.xxx.xxx.122 |
2019-10-30 08:40 |
[#46] 換電制求救 最後修改時間: 2019-10-30 09:47:21 |
0925 正式會員 219.xxx.xxx.122 |
2019-10-30 09:47 |
[#47] 換電制求救 https://detail.tmall.com/item.htm?spm=a230r.1.14.60.7f3118aatRUDhJ&id=588544962625&ns=1&abbucket=6 最後修改時間: 2019-10-30 11:12:32 |
0925 正式會員 219.xxx.xxx.122 |
2019-10-30 11:11 |
[#48] 換電制求救 Crimping alone is handy and good for smaller cables. Must maintain conductive area at the joint same as the cable size, say 4sq mm, by adding solder. (same for high voltage cable joint) |
alexanderkoo 正式會員 49.xxx.xxx.17 |
2019-10-30 15:02 |