| 談天說地主旨 ﹝請按主旨作出回應﹞ 下頁 尾頁 | 寄件者 | 傳送日期
|
| [#1] 想裝抽油煙機 想裝好耐但吾知點選又怕自己D位好難裝。住老式屋，無公家煙道。正上方無廚櫃，煙喉應該要由機體上方向左轉引約六尺去窗口出街（現窗口位裝了抽氣扇）。 因灶位不深，少於 50cm， 裝傳統式機體前沿會凸得很出，想買傾斜式，但又怕吾岩裝。至怕買了師傅話吾啱裝。 |
lym 正式會員42.xxx.xxx.203 |
2020-04-04 22:35 | |
|
|
|||
| [#2] 想裝抽油煙機 如果你用煤氣, 最好去showroom拎抽油煙機單張, 然後搵客服免費叫cfu上來睇下有咩model裝到, 睇完佢會幫你揀一堆, 跟住你同cfu講話考慮下,然後買佢地或自己出去搵. |
new68u 會員 59.xxx.xxx.194 |
2020-04-04 22:42 |
| [#3] 想裝抽油煙機 無用煤氣，只係用電爐。 |
lym 正式會員 42.xxx.xxx.203 |
2020-04-04 22:46 |
| [#4] 想裝抽油煙機 If you can install convention type(basically useless due to higher level for better clearance with utensil), you would be able to install inclined type especially induction cooker being used.(less heat) More difficult part is round window opening.(replace the existing glass by acrylic sheet with round hole) I simply DIY. If you buy from Taobao, the duct size is different, in metric.(need to buy the duct as well, quite small when squeezed) I am using Misoko(from Pacific), made in Taiwan with auto degreasing by internal heater. Water washing is not useful. Should have both. 最後修改時間: 2020-04-05 05:45:03 |
alexanderkoo 正式會員 219.xxx.xxx.113 |
2020-04-05 05:43 |
| [#5] 想裝抽油煙機 我剛剛裝咗。之前係傳統式，用咗廿年。舊機深560mm，凸出了櫃面4寸多，成日撞到頭，都想換斜面式，用咗好多時間去搜尋資料，在吉之島見到有德國寶煙通式，機身淺了很多。期間再去上海街櫥櫃陳列室睇過，有sales 話德國寶冇貨，話唔夠吸力，建議我買另一牌子德格煙通式，可惜尺寸不合我。之後我又在吉之島，第二個sales 又係咁講，叫我買太平洋⋯⋯。但最後我都係買番德國寶。結果，嘈，吸力與傳統舊式一般。但我少煮嘢食。 試唔試，自己諗⋯⋯俾張想你睇，早兩星期前。  最後修改時間: 2020-04-05 10:07:27 |
Rhl 正式會員 138.xxx.xxx.241 |
2020-04-05 10:06 |
| [#6] 想裝抽油煙機 德國寶因地方關係我用左幾年，佢既輕觸式按制已經開始想打柴。 |
gogo2010 正式會員 1.xxx.xxx.140 |
2020-04-05 10:25 |
| [#7] 想裝抽油煙機 For conventional type, Panasonic/KDK should be the best based on low price level, around $1600 only. Check the opening dimensions if duct runs through the cabinet. Mine was on left hand side(single fan), so can't change to new one with opening in the middle. Therefore, added an inline booster fan. Inclined one was installed in village house. 最後修改時間: 2020-04-05 13:03:21 |
alexanderkoo 正式會員 219.xxx.xxx.113 |
2020-04-05 13:02 |
| [#8] 想裝抽油煙機 呢類咪冇咁頂頭，不過呢部個扇葉唔可以拆出嚟清潔。  |
沉默的膏蟹 正式會員 14.xxx.xxx.203 |
2020-04-05 13:10 |
| [#9] 想裝抽油煙機 上面冇廚櫃其實普通台式同斜面果d都唔會唔啱裝。 |
沉默的膏蟹 正式會員 14.xxx.xxx.203 |
2020-04-05 13:14 |
| [#10] 想裝抽油煙機 The air inlet is closer to the cooker so more effective. In industry, for extraction gas heavier than air, ducts are installed with inlet at low level. Can be opened up for cleaning but more work in dissembly.(same for Western chimney type) Haven't tried that. Now, having auto cleaning via infra red. Taobao, much cheaper and more choices. |
alexanderkoo 正式會員 219.xxx.xxx.113 |
2020-04-05 13:16 |
| [#11] 想裝抽油煙機 ＞＞上面冇廚櫃其實普通台式同斜面果d都唔會唔啱裝。 理論上應該易D添。最多明喉屈突D。 |
lym 正式會員 42.xxx.xxx.203 |
2020-04-05 13:57 |
| [#12] 想裝抽油煙機 另外#5張相裝隱藏式咪得。 |
沉默的膏蟹 正式會員 14.xxx.xxx.203 |
2020-04-05 14:40 |
| [#13] 想裝抽油煙機 上面無㕑櫃又空擴，見到和喜歡任何款式都装得，都要問咁耐? |
KS 正式會員 182.xxx.xxx.192 |
2020-04-05 15:32 |
| [#14] 想裝抽油煙機 第二個sales 又係咁講，叫我買太平洋⋯⋯。＜ 用了21年，仍正常工作中。 |
0925 正式會員 218.xxx.xxx.115 |
2020-04-05 15:33 |
| [#15] 想裝抽油煙機 太平洋同金雅典呢d臺灣野都穩陣。 |
沉默的膏蟹 正式會員 14.xxx.xxx.203 |
2020-04-05 16:02 |
| [#16] 想裝抽油煙機 望緊呢款。話係台灣野。  |
lym 正式會員 42.xxx.xxx.203 |
2020-04-05 16:36 |
| [#17] 想裝抽油煙機 香港賣D機度來度去都係好大部，裝係應該裝到，但之後煮野空間會好吾方便。見老淘有D細機又吾貴想諗下自己裝（抽風效果當然差D）。出風口現在有個方型抽氣扇，要拆下換上開孔玻璃接上抽油煙機出風管。想請問下是否一般玻璃舖或做相架D地方可比尺吋佢地界？  |
lym 正式會員 209.xxx.xxx.4 |
2020-04-20 10:41 |
| [#18] 想裝抽油煙機 買太平洋啦，好多所謂名牌都是它代工做，我用了22年，重工作緊。 |
KS 正式會員 223.xxx.xxx.16 |
2020-04-20 10:45 |
| [#19] 想裝抽油煙機 我都想，但裝左真行埋去灶前煮野都有難度。 最後修改時間: 2020-04-20 10:49:26 |
lym 正式會員 209.xxx.xxx.4 |
2020-04-20 10:49 |
| [#20] 想裝抽油煙機 As mentioned before , scrap pc. of acrylic sheet with round hole cut by jigsaw. Must support the sheet more firmly to avoid chipping. Glass is hard and expensive to work with, would break at the sides. |
alexanderkoo 正式會員 223.xxx.xxx.103 |
2020-04-21 12:34 |
